Asus P3C-LS P3C-LS User Manual - Page 51

SCSI Connection and Termination Information

Get Asus P3C-LS PDF manuals and user guides View all Asus P3C-LS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

3. HARDWARE SETUP SCSI Connection and Termination Information Each SCSI channel is like a water hose where the inside must be opened and the ends must be closed. Each connector, whether 68 pins or 50 pins may have single or double-ended configurations. For Single-Ended configurations, the Termination for that particular channel must be set to Enabled in 4.4.3 PCI Configuration. For Double-ended configurations, the Termination for that particular channel must be set to Disabled in 4.4.3 PCI Configuration. Each channel may have up to 15 devices (ID#0-15, with #7 reserved for the chipset). The onboard Adaptec AIC-7892B chipset (optional) incorporates an advanced multimode I/O cell that supports both single-ended (SE) and low voltage differential (LVD) devices. With Ultra160 devices, the SCSI bus platform performs at full Ultra160 speeds (up to 80 MB/sec in 8-bit mode and up to 160 MB/sec in 16-bit mode) and extended cabling 12m (or 25m in a point-to-point configuration). When an SE device is attached, the bus defaults to an SE speed and cable length. In mixed environments of LVD and SE devices, the onboard host adapter can be coupled with the Adaptec AIC-3860Q transceiver chipset (optional) to bridge the compatibility gap. By dividing the SCSI bus into independent SE and low voltage differential (LVD) segments, the transceiver chipset supports legacy devices without limiting performance and cable length on the LVD segment. NOTE: Ultra160 devices do not have termination jumpers so a terminator block on the SCSI cable is needed. If your end devices have its own termination, you may use it instead. SCSI Connection Examples PCI Bus 3. H/W SETUP Connectors LVD Devices P3C-LS / L / S Adaptec AIC-7892B Chipset Ultra160 SCSI Connector Wide SCSI Connector PCI-to-Ultra3 (LVD) LVD Mode L S SE Mode Adaptec AIC-3860Q Chipset Disk 1 Disk 2 Disk 3 Single-Ended Devices CD-ROM Scanner Tape P3C-LS/L/S Mixed LVD and Single-Ended Device Configurations ASUS P3C-L / P3C-S / P3C-LS User's Manual 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
ASUS P3C-L / P3C-S / P3C-LS User’s Manual
51
3. HARDWARE SETUP
Connectors
3. H/W SETUP
SCSI Connection and Termination Information
Each SCSI channel is like a water hose where the inside must be opened and the
ends must be closed. Each connector, whether 68 pins or 50 pins may have single or
double-ended configurations. For Single-Ended configurations, the Termination for
that particular channel must be set to Enabled in
4.4.3 PCI Configuration
. For
Double-ended configurations, the Termination for that particular channel must be
set to Disabled in
4.4.3 PCI Configuration
. Each channel may have up to 15 de-
vices (ID#0-15, with #7 reserved for the chipset).
The onboard Adaptec AIC-7892B chipset (optional) incorporates an advanced
multimode I/O cell that supports both single-ended (SE) and low voltage differential
(LVD) devices. With Ultra160 devices, the SCSI bus platform performs at full Ul-
tra160 speeds (up to 80 MB/sec in 8-bit mode and up to 160 MB/sec in 16-bit mode)
and extended cabling 12m (or 25m in a point-to-point configuration). When an SE
device is attached, the bus defaults to an SE speed and cable length.
In mixed environments of LVD and SE devices, the onboard host adapter can be coupled
with the Adaptec AIC-3860Q transceiver chipset (optional) to bridge the compatibility
gap. By dividing the SCSI bus into independent SE and low voltage differential (LVD)
segments, the transceiver chipset supports legacy devices without limiting performance
and cable length on the LVD segment.
NOTE:
Ultra160 devices do not have termination jumpers so a terminator block on
the SCSI cable is needed. If your end devices have its own termination, you may use
it instead.
SCSI Connection Examples
P3C-LS/L/S Mixed LVD
and Single-Ended Device Configurations
P3C-LS / L / S
LVD Devices
Single-Ended Devices
Scanner
Tape
Disk 2
Disk 3
Disk 1
CD-ROM
PCI Bus
Adaptec
AIC-3860Q
Chipset
Adaptec
AIC-7892B
Chipset
LVD Mode
Wide SCSI Connector
Ultra160 SCSI
Connector
PCI-to-Ultra3 (LVD)
SE Mode
S
L