Asus PSCH-SR SATA PSCH-SR User Manual English Version - Page 43

ASUS PSCH-SR motherboard, IDE connectors 40-1 pin PRI_IDE1 [blue], SEC_IDE1 [black

Get Asus PSCH-SR SATA PDF manuals and user guides View all Asus PSCH-SR SATA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

5. IDE connectors (40-1 pin PRI_IDE1 [blue], SEC_IDE1 [black) This connector supports the provided UltraATA100 IDE hard disk ribbon cable. Connect the cable's blue connector to the primary (recommended) or secondary IDE connector, then connect the gray connector to the UltraATA100 slave device and the black connector to the UltraATA100 master device. It is recommended that you connect non-UltraATA100 devices to the secondary IDE connector. If you install two hard disks, you must configure the second drive as a slave device by setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings. BIOS supports specific device bootup. You may configure two hard disks to be both master devices with two ribbon cables - one for the primary IDE connector and another for the secondary IDE connector. • Pin 20 on each IDE connector is removed to match the covered hole on the UltraATA cable connector. This prevents incorrect orientation when you connect the cables. • The hole near the blue connector on the UltraATA100 cable is intentional. • For UltraATA IDE devices, use the 80-conductor IDE cable. ® PSCH-SR PSCH-SR IDE Connectors SEC_IDE1 PIN 1 PRI_IDE1 PIN 1 NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. ASUS PSCH-SR motherboard 2-25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
ASUS PSCH-SR motherboard
2-25
5.
IDE connectors (40-1 pin PRI_IDE1 [blue], SEC_IDE1 [black)
This connector supports the provided UltraATA100 IDE hard disk
ribbon cable. Connect the cable’s blue connector to the primary
(recommended) or secondary IDE connector, then connect the gray
connector to the UltraATA100 slave device and the black connector to
the UltraATA100 master device. It is recommended that you connect
non-UltraATA100 devices to the secondary IDE connector. If you install
two hard disks, you must configure the second drive as a slave device
by setting its jumper accordingly. Refer to the hard disk documentation
for the jumper settings. BIOS supports specific device bootup.
You may
configure two hard disks to be both master devices with two ribbon
cables – one for the primary IDE connector and another for the
secondary IDE connector.
•
Pin 20 on each IDE connector is removed to match the covered
hole on the UltraATA cable connector. This prevents incorrect
orientation when you connect the cables.
•
The hole near the blue connector on the UltraATA100 cable is
intentional.
•
For UltraATA IDE devices, use the 80-conductor IDE cable.
PSCH-SR
PSCH-SR IDE Connectors
NOTE:
Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
SEC_IDE1
PRI_IDE1
PIN 1
PIN 1