Beko HII64430GT User Manual - Page 21

Beko HII64430GT Manual

Get Beko HII64430GT PDF manuals and user guides View all Beko HII64430GT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

• In low power positions, a regular on-off sound can be heard due to the operating principle. • Sound can occur while heating an empty pan. Such sound will disappear when you add water or food in it. • Noise of the fan which is used to cool the electronic system can be heard. Sensor Calibration and Error Messages When the supply power is applied, hob control system performs calibration depending on the sensor, glass and ambient conditions. Do not cover the glass part of the sensor with anything during calibration. Hob control system should also not be exposed to strong light sources such as sun light, strong halogen lamps and etc. Table-3:Error codes and error sources Cause of error Display Ambient light is too high Fl Fluorescent lamp F2 Sensor is covered with a bright F3 substance Ambient light is fluctuating strongly F4 Calibration error AX Induction hardware error EX (x = "0.. ..9") Sample application: Following lightning conditions will allow a smooth calibration: Illumination with a bulb without a reflector (100W, dull) 70 cm above the glass ceramic hob. After a successful calibration, it is warranted that the hob will operate as intended even under a strong illumination such as halogen spot lamp wit reflector (50 V . In case of an error, the calibration is repeated until the ambient conditions allow a successful calibration. The operation of the hob control is only possible, if the calibration of all sensors were successfully completed. After successful finished calibration process the control tolerates a very high rate of ambient light. During the operation of the hob control, it continuously adopts and recalibrates itself towards the changes in the ambient conditions. 0 Please see Table 3 for information on explanations related to the error messages hat can appear on the touch control display. In the event that the touch control surface is losed for a period longer than 10 seconds, he entire control system will be deactivated and a warning signal will sound. Also "F" flashes on the hotplate display. 0 If the surface of the touch control is exposed to dense vapour, the entire control system will be deactivated and a warning signal may be given. 0 Keep the surface of the touch panel clean. Otherwise, malfunctioning may occur. 21/EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
•
In
low
power
positions,
a
regular
on
-off
sound
can
be
heard
due
to
the
operating
principle.
•
Sound
can
occur
while
heating
an
empty
pan.
Such
sound
will
disappear
when
you
add
water
or
food
in
it.
•
Noise
of
the
fan
which
is
used
to
cool
the
electronic
system
can
be
heard.
Sensor
Calibration
and
Error
Messages
When
the
supply
power
is
applied,
hob
control
system
performs
calibration
depending
on
the
sensor,
glass
and
ambient
conditions.
Do
not
cover
the
glass
part
of
the
sensor
with
anything
during
calibration.
Hob
control
system
should
also
not
be
exposed
to
strong
light
sources
such
as
sun
light,
strong
halogen
lamps
and
etc.
Table-3:Error
codes
and
error
sources
Cause
of
error
Display
Ambient
light
is
too
high
Fl
Fluorescent
lamp
F2
Sensor
is
covered
with
a
bright
substance
F3
Ambient
light
is
fluctuating
strongly
F4
Calibration
error
AX
Induction
hardware
error
EX
(x
=
"0.
..
.9")
Sample
application:
Following
lightning
conditions
will
allow
a
smooth
calibration:
Illumination
with
a
bulb
without
a
reflector
(100W,
dull)
70
cm
above
the
glass
ceramic
hob.
After
a
successful
calibration,
it
is
warranted
that
the
hob
will
operate
as
intended
even
under
a
strong
illumination
such
as
halogen
spot
lamp
wit
reflector
(50
V
.
In
case
of
an
error,
the
calibration
is
repeated
until
the
ambient
conditions
allow
a
successful
calibration.
The
operation
of
the
hob
control
is
only
possible,
if
the
calibration
of
all
sensors
were
successfully
completed.
After
successful
finished
calibration
process
the
control
tolerates
a
very
high
rate
of
ambient
light.
During
the
operation
of
the
hob
control,
it
continuously
adopts
and
recalibrates
itself
towards
the
changes
in
the
ambient
conditions.
0
Please
see
Table
3
for
information
on
explanations
related
to
the
error
messages
hat
can
appear
on
the
touch
control
display.
In
the
event
that
the
touch
control
surface
is
losed
for
a
period
longer
than
10
seconds,
he
entire
control
system
will
be
deactivated
and
a
warning
signal
will
sound.
Also
"F"
flashes
on
the
hotplate
display.
0
If
the
surface
of
the
touch
control
is
exposed
to
dense
vapour,
the
entire
control
system
will
be
deactivated
and
a
warning
signal
may
be
given.
0
Keep
the
surface
of
the
touch
panel
clean.
Otherwise,
malfunctioning
may
occur.
21/EN