BenQ Joybee GP1 GP1 User Manual - Page 26

Auto-adjusting the image, Fine-tuning the image clarity, Correcting keystone, MENU/EXIT, DISPLAY

Get BenQ Joybee GP1 PDF manuals and user guides View all BenQ Joybee GP1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Auto-adjusting the image In some cases, you may need to optimize the picture quality. • Using the remote control Press AUTO. • Using the OSD menu 1. Press MENU/EXIT and then presss / until the DISPLAY menu is highlighted. 2. Press to highlight Auto and press MODE/ ENTER. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality. The current source information will be displayed in the upper left corner of the screen for 3 seconds. • The screen will be blank while AUTO is functioning. • This function is only available when PC signal (analog RGB) is selected. Fine-tuning the image clarity 1. Rotate the focus ring to sharpen the image. Correcting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen. To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of these steps. • Using the remote control Press / on the projector or remote control to display the Keystone correction page. Press to correct keystoning at the top of the image. Press to correct keystoning at the bottom of the image. • Using the OSD menu 1. Press MENU/EXIT and then press / until the DISPLAY menu is highlighted. 2. Press to highlight Keystone and press MODE/ENTER. The Keystone correction page displays. 3. Press to correct keystoning at the top of the image or press to correct keystoning Press / . at the bottom of the image. 26 Operation Press / .

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
Operation
26
Auto-adjusting the image
In some cases, you may need to optimize the picture quality.
•
Using the remote control
Press
AUTO
.
•
Using the OSD menu
1.
Press
MENU/EXIT
and then presss
/
until the
DISPLAY
menu is highlighted.
2.
Press
to highlight Auto and press
MODE/
ENTER
.
Within 3 seconds, the built-in Intelligent Auto
Adjustment function will re-adjust the values of Frequency and Clock to provide the best
picture quality.
The current source information will be displayed in the upper left corner of the screen for 3
seconds.
•
The screen will be blank while AUTO is functioning.
•
This function is only available when PC signal (analog RGB) is selected.
Fine-tuning the image clarity
1.
Rotate the focus ring to sharpen the image.
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the
top or bottom. It occurs when the projector is not perpendicular to the screen.
To correct this, besides adjusting the height of the projector, you will need to manually
correct it following one of these steps.
•
Using the remote control
Press
/
on the projector or remote control
to display the Keystone correction page. Press
to correct keystoning at the top of the image. Press
to correct keystoning at the bottom of the image.
•
Using the OSD menu
1.
Press
MENU/EXIT
and then press
/
until the
DISPLAY
menu is highlighted.
2.
Press
to highlight
Keystone
and press
MODE/ENTER
. The
Keystone
correction
page displays.
3.
Press
to correct keystoning at the top of
the image or press
to correct keystoning
at the bottom of the image.
Press
/
.
Press
/
.