BenQ Joybee GP1 GP1 User Manual - Page 33

Personalizing the projector menu display, Shutting down the projector - led

Get BenQ Joybee GP1 PDF manuals and user guides View all BenQ Joybee GP1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Personalizing the projector menu display The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect the projection settings, operation, or performance. • Menu display time in the SYSTEM SETUP: Advanced > Menu Settings menu sets the length of time the OSD will remain active after your last key press. The time length ranges from 5 to 30 seconds in 5-second increments. Use / to select a suitable time frame. • Menu position in the SYSTEM SETUP: Advanced > Menu Settings menu sets the OSD position in five locations. Use / to select a preferred position. • Language in the SYSTEM SETUP: Basic menu sets your familiar language for the OSD menus. Use / to select your language. • Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen to be displayed during projector start-up. Use / to select a screen. Shutting down the projector 1. Press II Power and a confirmation message displays prompting you. If you don't respond in a few seconds, the message will disappear. 2. Press II Power a second time. The Power LED indicator flashes blue fast and Ring LED indicator lights blue, the projection lamp shuts down, and the fans will continue to run for approximately 90 seconds to cool down the projector. 3. Once the cooling process finishes, the Power LED indicator flashes blue slowly and Ring LED indicator lights blue and fans stop. 4. Disconnect the power cord from the wall socket if the projector will not be used in an extended period of time. • To protect the lamp, the projector will not respond to any commands during the cooling process. • Do not unplug the power cord before the projector shutdown sequence is complete or during the 90-second cooling down process. • If the projector is not properly shut down, to protect the lamp, when you attempt to re-start the projector, the fans will run for a few minutes to cool down. Press Power again to start the projector after the fans stop and the Power LED indicator flashes blue slowly and Ring LED indicator lights blue. Operation 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
Operation
33
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The
following settings do not affect the projection settings, operation, or performance.
•
Menu display time
in the
SYSTEM SETUP: Advanced
>
Menu Settings
menu sets the
length of time the OSD will remain active after your last key press. The time length
ranges from 5 to 30 seconds in 5-second increments. Use
/
to select a suitable time
frame.
•
Menu position
in the
SYSTEM SETUP: Advanced
>
Menu Settings
menu sets the OSD
position in five locations. Use
/
to select a preferred position.
•
Language
in the
SYSTEM SETUP: Basic
menu sets your familiar language for the OSD
menus. Use
/
to select your language.
•
Splash Screen
in the
SYSTEM SETUP: Basic
menu sets a preferred logo screen to be
displayed during projector start-up. Use
/
to select a screen.
Shutting down the projector
1.
Press
Power
and a confirmation message
displays prompting you.
If you don't respond in a few seconds, the
message will disappear.
2.
Press
Power
a second time. The
Power LED
indicator
flashes blue fast and
Ring LED
indicator
lights blue, the projection lamp shuts
down, and the fans will continue to run for approximately 90 seconds to cool down
the projector.
3.
Once the cooling process finishes, the
Power LED indicator
flashes blue slowly and
Ring LED indicator
lights blue and fans stop.
4.
Disconnect the power cord from the wall socket if the projector will not be used in an
extended period of time.
•
To protect the lamp, the projector will not respond to any commands during the cooling
process.
•
Do not unplug the power cord before the projector shutdown sequence is complete or
during the 90-second cooling down process.
•
If the projector is not properly shut down, to protect the lamp, when you attempt to re-start
the projector, the fans will run for a few minutes to cool down. Press Power again to start
the projector after the fans stop and the Power LED indicator flashes blue slowly and Ring
LED indicator lights blue.
I
I
I
I