Beretta PICO 380 Instruction Manual - Page 49

Troubleshooting

Get Beretta PICO 380 PDF manuals and user guides View all Beretta PICO 380 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

DISASSEMBLY Depress the pin in the center of the floor plate until the floor plate can slide off the magazine bottom. The floor plate retainer, magazine spring and follower can now be removed. NOTE: The retaining plate is under spring tension from the magazine spring. Removing the floor plate will release the spring, make sure to retain the spring and retaining plate when the floor plate is removed. ASSEMBLY Install the follower then install the magazine spring with the higher end of the magazine spring to the front of the magazine. Compress the magazine spring into the magazine body with the retaining plate with the boss facing down and slide the floor plate into position. The boss on the retaining plate will lock into the floor plate when the magazine is assembled properly. Then press the retaining plate pin down and slide grip extension on the retaining plate rails. When it snaps onto pin it should be secure. TROUBLESHOOTING WARNING: Do not attempt to make repairs to any firearm without proper knowledge or training. Do not alter parts or use substitute parts not made by Beretta. Any necessary alterations or adjustments to the operating mechanism should be performed by the Manufacturer or by its Local Official Distributor. WARNING: Do not attempt to alter the internal parts of your pistol's firing mechanism. Altering internal parts can cause unsafe condition. WARNING: Altering the internal parts of your pistol's firing mechanism voids the manufacturer's warranty. 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
49
DISASSEMBLY
Depress the pin in the center of the floor plate until the floor plate can
slide off the magazine bottom. The floor plate retainer, magazine spring
and follower can now be removed.
NOTE:
The retaining plate is under spring tension from the magazine
spring. Removing the floor plate will release the spring, make sure to
retain the spring and retaining plate when the floor plate is removed.
ASSEMBLY
Install the follower then install the magazine spring with the higher end
of the magazine spring to the front of the magazine. Compress the
magazine spring into the magazine body with the retaining plate with
the boss facing down and slide the floor plate into position. The boss
on the retaining plate will lock into the floor plate when the magazine is
assembled properly. Then press the retaining plate pin down and slide
grip extension on the retaining plate rails. When it snaps onto pin it
should be secure.
TROUBLESHOOTING
WARNING
:
Do not attempt to make repairs to any firearm without
proper knowledge or training. Do not alter parts or use substitute parts
not made by Beretta. Any necessary alterations or adjustments to the
operating mechanism should be performed by the Manufacturer or by its
Local Official Distributor.
WARNING
:
Do not attempt to alter the internal parts of your pistol’s
firing mechanism. Altering internal parts can cause unsafe condition.
WARNING
:
Altering the internal parts of your pistol’s firing mechanism
voids the manufacturer’s warranty.