Brother International CS-8072 Users Manual - English - Page 74

Mechanical trouble, Alarm, When the sewing machine is restarted - power cord

Get Brother International CS-8072 PDF manuals and user guides View all Brother International CS-8072 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

CONTENTS BEFORE USE SEWING Mechanical trouble Symptom 1. Fabric is not fed properly 2. Needle breaks 3. Machine does not start Probable cause Remedy 1. Feed dog is lowered. 1. Raise the feed dog with the feed dog position switch. 2. Stitch length is set at no feeding. 2. Set stitch length properly. 3. The combination of selected stitch and 3. Change presser foot to correct one. presser foot is not correct. 4. Correct needle is not being used. 4. Change to proper needle. 5. Thread is entangled. 5. Remove thread-ends in the race or inner shuttle. 1. Needle is not correctly inserted. 1. Set needle properly. 2. Correct needle is not used. 2. Change to proper needle. 3. The combination of fabric, thread and needle is not correct. 3. Check the "FABRIC/THREAD/NEEDLE COMBINATION CHART" on page 26. 4. The fabric is pulled too much. 4. Guide the fabric allowing it to sew without pulling. 1. "START/STOP" button is not pressed. 1. Press "START/STOP" button. 2. Main power switch is in the off position. 2. Turn the power on. 3. Presser foot is not lowered. 3. Lower the presser foot. Note - If the power goes out while the sewing machine is being operated: Turn off the sewing machine and unplug its power cord. When the sewing machine is restarted, operate it correctly according to the operating procedure. Alarm • When operating correctly : 1 beep • When operating incorrectly : 2 beeps or 4 beeps UTILITY STITCHES MAINTENANCE SEWING CHART PATTERNS (PROGRAMMED IN MACHINE) 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
71
Mechanical trouble
Probable cause
1.
Feed dog is lowered.
2.
Stitch length is set at no feeding.
3.
The combination of selected stitch and
presser foot is not correct.
4.
Correct needle is not being used.
5.
Thread is entangled.
1.
Needle is not correctly inserted.
2.
Correct needle is not used.
3.
The combination of fabric, thread and
needle is not correct.
4.
The fabric is pulled too much.
1.
“START/STOP” button is not pressed.
2.
Main power switch is in the off position.
3.
Presser foot is not lowered.
Remedy
1.
Raise the feed dog with the feed dog
position switch.
2.
Set stitch length properly.
3.
Change presser foot to correct one.
4.
Change to proper needle.
5.
Remove thread-ends in the race or
inner shuttle.
1.
Set needle properly.
2.
Change to proper needle.
3.
Check the “FABRIC/THREAD/NEEDLE
COMBINATION CHART” on page 26.
4.
Guide the fabric allowing it to sew
without pulling.
1.
Press “START/STOP” button.
2.
Turn the power on.
3.
Lower the presser foot.
Symptom
1.
Fabric is not fed properly
2.
Needle breaks
3.
Machine does not start
Note
–
If the power goes out while the sewing machine is being operated:
Turn off the sewing machine and unplug its power cord.
When the sewing machine is restarted, operate it correctly according to the operating procedure.
•
When operating correctly : 1 beep
•
When operating incorrectly : 2 beeps or 4 beeps
Alarm
CONTENTS
BEFORE USE
SEWING
UTILITY STITCHES
MAINTENANCE
SEWING CHART
PATTERNS
(PROGRAMMED IN
MACHINE)