Brother International NX570Q Operation Manual

Brother International NX570Q Manual

Get Brother International NX570Q PDF manuals and user guides View all Brother International NX570Q manuals
Add to My Manuals
Save this manual to your list of manuals

Brother International NX570Q manual content summary:

  • Brother International NX570Q | Operation Manual - Page 1
    Operation Manual Computerized Sewing Machine Product Code: 885-U22 Read before use. GETTING READY SEWING BASICS Read when additional information is required. UTILITY STITCHES APPENDIX
  • Brother International NX570Q | Operation Manual - Page 2
  • Brother International NX570Q | Operation Manual - Page 3
    Please read these safety instructions before attempting to use the machine. DANGER - To reduce the risk of electric shock: 1 Always unplug the machine from the electrical outlet immediately after using, when cleaning, when making any user servicing adjustments mentioned in this manual, or if you are
  • Brother International NX570Q | Operation Manual - Page 4
    when sewing, and follow careful instruction when freehand stitching so that . 7 For a longer service life: • When storing troubleshooting table in the back of the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Brother
  • Brother International NX570Q | Operation Manual - Page 5
    FOR USERS IN THE UK, EIRE, MALTA AND CYPRUS ONLY IMPORTANT • In the event of replacing the plug fuse, use a fuse approved by ASTA to BS 1362, i.e. carrying the mark, rating as marked on plug. • Always replace the fuse cover. Never use plugs with the fuse cover omitted. • If the available
  • Brother International NX570Q | Operation Manual - Page 6
    Contents IMPORTANT SAFETY INSTRUCTIONS 1 Introduction ...7 Sewing Machine Features ...7 Accessories ...8 Included 28 Threading the upper thread ...28 Threading the needle ...31 Threading the needle manually (without using the needle threader 33 Using the twin needle ...33 Pulling up
  • Brother International NX570Q | Operation Manual - Page 7
    SEWING BASICS 49 Sewing ...50 General sewing procedure ...50 Positioning the fabric ...51 Starting to sew...52 Securing the stitching ...54 Cutting the thread ...55 Adjusting the Thread Tension 57 Changing the tension of the upper thread ...57 Adjusting the Stitch Width and Length 58
  • Brother International NX570Q | Operation Manual - Page 8
    stitches...138 Care and Maintenance ...142 Restrictions on oiling...142 Cleaning the machine surface ...142 Cleaning the race ...142 Troubleshooting ...144 Frequent troubleshooting topics ...144 Upper thread tightened up ...144 Tangled thread on wrong side of fabric ...145 Incorrect thread tension
  • Brother International NX570Q | Operation Manual - Page 9
    . Before using this sewing machine, carefully read the "IMPORTANT SAFETY INSTRUCTIONS" (page 1), and then study this manual for the correct operation of the various functions. In addition, after you have finished reading this manual, store it where it can quickly be accessed for future reference
  • Brother International NX570Q | Operation Manual - Page 10
    Accessories After opening the box, check that the following accessories are included. If any item is missing or damaged, contact your dealer. Included accessories The following items should also be included in the box. Note (For U.S.A. only) z Foot controller: Model N5V This foot controller can
  • Brother International NX570Q | Operation Manual - Page 11
    (XE1094-101) 30 Operation manual XZ5082-001 31 Quick reference guide SA156 SFB (XA5539-151) 32 Hard case X58358-021 33 Accessory bag X59296-121 34 Disc-shaped screwdriver X59476-021 35 Stitch pattern plate **Contact your dealer or the nearest authorized service
  • Brother International NX570Q | Operation Manual - Page 12
    cover when threading the upper thread. c Spool pin Place a spool of thread on the spool pin. d Bobbin winding thread guide and pretension disk Pass the thread under this thread guide and around the pretension disk when winding the bobbin thread. e Top cover Open the top cover to place the spool of
  • Brother International NX570Q | Operation Manual - Page 13
    disk when using the needle threader to thread the needle. c Needle bar thread guide Pass the upper thread through the needle bar thread guide. d Needle plate The needle plate is marked with guides to help sew straight seams. e Needle plate cover Remove the needle plate cover to clean the bobbin
  • Brother International NX570Q | Operation Manual - Page 14
    Operation buttons The operation buttons help you to easily perform various basic sewing machine operations. a "Start/Stop" button Press the "Start/Stop" button to start or stop sewing. The machine sews at a slow speed at the beginning of sewing while the button is depressed. When sewing is
  • Brother International NX570Q | Operation Manual - Page 15
    . l Character stitch key Press this key to select a character stitch. Each time this key is pressed, the font switches to one of the three available. m Manual memory key Press this key to save the adjusted stitch width and length settings. n Reset key Press this key to reset the selected stitch to
  • Brother International NX570Q | Operation Manual - Page 16
    14
  • Brother International NX570Q | Operation Manual - Page 17
    Winding the bobbin 22 Installing the bobbin 26 Upper Threading ...28 Threading the upper thread 28 Threading the needle 31 Threading the needle manually (without using the needle threader 33 Using the twin needle 33 Pulling up the bobbin thread 36 Replacing the Needle 37 Needle precautions
  • Brother International NX570Q | Operation Manual - Page 18
    GETTING READY Turning the Machine On/Off This section explains how to turn the sewing machine on and off. Power supply precautions Be sure to observe the following precautions concerning the power supply. WARNING ● Use only regular household electricity for the power source. Using other power
  • Brother International NX570Q | Operation Manual - Page 19
    Turning on the machine Turning off the machine Prepare the included power cord. When you are finished using the sewing machine, Make sure that the sewing machine is turned turn it off. In addition, before transporting the sewing machine to another location, be sure to turn it off. 1 a off
  • Brother International NX570Q | Operation Manual - Page 20
    GETTING READY Understanding the LCD Screens The LCD screen, located on the front at the right of the sewing machine, displays the settings for the selected stitch and error messages if operations are performed incorrectly.When the sewing machine is turned on, the LCD comes on and the following
  • Brother International NX570Q | Operation Manual - Page 21
    Changing the Machine Settings Various sewing machine operations and sewing settings can be changed. Changing the settings Press or (Stitch length keys) until the 1 c stitch or machine attribute that you wish to set The general procedure for changing machine settings is described below. is
  • Brother International NX570Q | Operation Manual - Page 22
    GETTING READY ■ List of stitch or machine attributes The stitch or machine attributes that can be set are listed below. For details on each attribute, refer to the corresponding reference page. Attribute Check pattern Icon Details Allows combined patterns to be checked. Reference page 121
  • Brother International NX570Q | Operation Manual - Page 23
    Adjusting the brightness of the LCD Changing the screen language The language used in the screens that are displayed The brightness of the LCD can be adjusted. can be changed to one of the many available. 1 Press (Settings key) in the operation a panel, and then press or (Stitch length
  • Brother International NX570Q | Operation Manual - Page 24
    GETTING READY Winding/Installing the Bobbin This section describes how to wind the thread onto the bobbin, and then insert the bobbin thread. Bobbin precautions Be sure to observe the following precautions concerning the bobbin. CAUTION ● Only use the bobbin (part code: SA156, SFB(XA5539-151
  • Brother International NX570Q | Operation Manual - Page 25
    Turn on the sewing machine. a Place the spool of thread for the bobbin onto f the spool pin. Slide the spool onto the pin so that the spool is horizontal and the thread unwinds to the front at the bottom. 1 Open the top cover. b Place the bobbin on the bobbin winder shaft so c that the spring
  • Brother International NX570Q | Operation Manual - Page 26
    thread near the spool with h your right hand, as shown, pull the thread with your left hand, and then pass the thread behind the thread guide cover and to the front. 1 a a Spool cap (small) b Spool (cross-wound thread) c Space z When using thread that winds off quickly, such as transparent nylon
  • Brother International NX570Q | Operation Manual - Page 27
    thread will become wrapped around the bobbin winder shaft. Pass the end of the thread through the guide l slit in the bobbin winder seat, and then pull the thread to the right to cut it. 1 a Guide slit in bobbin winder seat (with built-in cutter) X The thread is cut to a suitable length
  • Brother International NX570Q | Operation Manual - Page 28
    is on the left, and then, after pulling the thread firmly around the tab with your left hand as shown, lightly pull the thread to guide it through the slit. 1 a Tab CAUTION ● Be sure to install the bobbin so that the thread unwinds in the correct direction, otherwise the thread may
  • Brother International NX570Q | Operation Manual - Page 29
    of the bobbin case. If it is not inserted correctly, reinsert the thread. 1 While lightly holding down bobbin with your g right hand as shown, guide the thread through the slit (1 and 2). • At this time, check that the bobbin easily rotates counterclockwise. Then, pull the thread toward you to
  • Brother International NX570Q | Operation Manual - Page 30
    for positioning the spool for the upper thread and threading the needle are described. CAUTION ● When threading the upper thread, carefully follow the instructions. If the upper threading is not correct, the thread may become tangled and the needle may bend or break. Threading the upper thread
  • Brother International NX570Q | Operation Manual - Page 31
    Press ("Needle Position" button) once or c twice to raise the needle. Place the spool of thread onto the spool pin. f Slide the spool onto the pin so that the spool is horizontal and the thread unwinds to the front at the bottom. 1 1 a "Needle Position" button X The needle is correctly
  • Brother International NX570Q | Operation Manual - Page 32
    with your h right hand, pull the thread with your left hand, and then pass the thread behind the thread guide cover and to the front. 1 a Thread guide cover Pass the thread under the thread guide plate, i and then pull it up. Note z If the presser foot has been lowered and the shutter is
  • Brother International NX570Q | Operation Manual - Page 33
    cannot be used, refer to "Threading the needle manually (without using the needle threader)" (page 33). Pull the end of the ) of thread after passing it through the thread guide disks (marked "7"). 21 2 1 a Notch of the thread guide b Thread guide disk 1 a 80 mm (3 inches) or more
  • Brother International NX570Q | Operation Manual - Page 34
    GETTING READY Lower the needle threader lever on the left d side of the machine until it clicks, and then slowly return the lever to its original position. 1 Raise the presser foot lever, pass the end of the e thread through the presser foot, and then pull out about 5 cm (2 inches) of thread
  • Brother International NX570Q | Operation Manual - Page 35
    that can be sewn with the Thread the machine to the needle bar thread a guide. twin needle, refer to "Stitch Settings" (page 134). • For details, to steps a through k of "Threading the upper thread" (page 28). Manually thread the left needle with the upper c thread. Pass the thread through the
  • Brother International NX570Q | Operation Manual - Page 36
    cover • For details, refer to step h through j of "Threading the upper thread" (page 28). Without passing the thread through the needle h bar thread guide, manually thread the right needle. Pass the thread through the eye of the needle from the front. Place the upper thread spool for the needle on
  • Brother International NX570Q | Operation Manual - Page 37
    Select a stitch. k • For details on selecting a stitch, refer to "Selecting stitching" (page 72). Start sewing. m • For details on starting to sew, refer to "Starting to sew" (page 52). • For details on the stitches that can be sewn with the twin needle, refer to "Stitch Settings" (page 134).
  • Brother International NX570Q | Operation Manual - Page 38
    GETTING READY Pulling up the bobbin thread When making gathers or before free-motion quilting, first pull up the bobbin thread as described below. Insert the bobbin into the bobbin case. a • Refer to steps a through e of "Installing the bobbin" (page 26). Pull out about 10 cm (4 inches) of the
  • Brother International NX570Q | Operation Manual - Page 39
    observe these precautions is extremely dangerous, for example, if the needle breaks and fragments are dispersed. Be sure to read and carefully follow the instructions below. CAUTION ● Only use home sewing machine needles. Use of any other needle may bend the needle or damage the machine. ● Never use
  • Brother International NX570Q | Operation Manual - Page 40
    GETTING READY Needle types and their uses The sewing machine needle that should be used depends on the fabric and thread thickness. Refer to the following table when choosing the thread and needle appropriate for the fabric that you wish to sew. Fabric Type/Application Medium weight fabrics
  • Brother International NX570Q | Operation Manual - Page 41
    since the needle may break while the machine is being operated. screwdriver and a needle that has been determined to be straight according to the instructions in "Checking 1 Before using the needle, place the flat side of the the needle". needle on a flat surface and check that the distance
  • Brother International NX570Q | Operation Manual - Page 42
    GETTING READY Lower the presser foot lever. d While holding the needle with your left hand, g use the screwdriver to tighten the needle clamp screw. 1 a Presser foot lever Hold the needle with your left hand, and then e use a screwdriver to turn the needle clamp screw toward you (
  • Brother International NX570Q | Operation Manual - Page 43
    Replacing the Presser Foot The presser foot presses down on the fabric. Presser foot precautions 1 Replacing the presser foot Be sure to observe the following precautions concerning the presser feet. CAUTION ● Use the presser foot appropriate for the type of stitch that you wish to sew,
  • Brother International NX570Q | Operation Manual - Page 44
    GETTING READY Press the black button at the back of the d presser foot holder. a Raise the presser foot lever to check that the g presser foot is securely attached. b a Black button b Presser foot holder X The presser foot holder releases the presser foot. Place a different presser foot below
  • Brother International NX570Q | Operation Manual - Page 45
    Adjusting the pressure of the presser foot Removing the presser foot holder The presser foot pressure (the amount of pressure applied to the fabric by the presser foot) can be adjusted. Lower the presser foot lever. a 1 a Presser foot lever Remove the presser foot holder when cleaning the
  • Brother International NX570Q | Operation Manual - Page 46
    touch the presser foot. If the needle hits the presser foot, the needle may bend or break. ■ Attaching the walking foot Note z Thread the needle manually when using the walking foot, or only attach the walking foot after threading the needle using the needle threader. Remove the presser foot holder
  • Brother International NX570Q | Operation Manual - Page 47
    With a screwdriver, loosen the presser foot d holder screw, and then remove the walking foot. 1 a a Presser foot holder screw Attach the presser foot holder. e • For details, refer to "Removing the presser foot holder" (page 43). Memo z Only the straight stitch (with reinforcement stitching) and
  • Brother International NX570Q | Operation Manual - Page 48
    GETTING READY Sewing Cylindrical or Large Pieces When sewing cylindrical or large pieces of fabric, remove the flat bed attachment. Stitching cylindrical pieces Sewing large pieces of fabric Removing the flat bed attachment makes it easier to sew cylindrical pieces such as cuffs and pant legs
  • Brother International NX570Q | Operation Manual - Page 49
    wide table can 1 be stored attached to the hard case. 2 1 a Lower right corner b Sewing machine bed Note z The optional wide table is available through your brother dealer. Turn the screw at the bottom of each leg to d adjust their height so the wide table will be level with the sewing machine
  • Brother International NX570Q | Operation Manual - Page 50
    GETTING READY 48
  • Brother International NX570Q | Operation Manual - Page 51
    2 SEWING BASICS The necessary preparations for sewing are described in this chapter. Sewing ...50 General sewing procedure 50 Positioning the fabric 51 Starting to sew 52 Securing the stitching 54 Cutting the thread 55 Adjusting the Thread Tension 57 Changing the tension of the upper thread
  • Brother International NX570Q | Operation Manual - Page 52
    SEWING BASICS Sewing Basic sewing operations are described below. Before operating the sewing machine, read the following precautions. CAUTION ● While the machine is in operation, pay special attention to the needle location. In addition, keep your hands away from all moving parts such as the
  • Brother International NX570Q | Operation Manual - Page 53
    Positioning the fabric Be sure that the fabric pieces are sewn in the correct order and that the right and wrong sides of the fabric are aligned correctly. Turn on the sewing machine. a 2 The straight stitch (left needle position) is automatically selected. Press ("Needle Position" button)
  • Brother International NX570Q | Operation Manual - Page 54
    SEWING BASICS Starting to sew Press b ("Start/Stop" button) once. Once you are ready to start sewing, you can start the sewing machine. The sewing speed can be adjusted using either the sewing speed controller or the foot controller. Note Important: z When the foot controller is plugged in, ("
  • Brother International NX570Q | Operation Manual - Page 55
    Insert the foot controller plug into its jack on b the side of the sewing machine. 1 Once you are ready to start sewing, slowly e press down on the foot controller. Pressing down on the foot controller increases the sewing speed; releasing the pressure on the foot controller decreases the
  • Brother International NX570Q | Operation Manual - Page 56
    SEWING BASICS Securing the stitching When sewing with the straight stitch, for example, at the end of an opening or where seams do not overlap, use reverse stitching or reinforcement stitching to secure the end of the thread. After sewing 3 to 5 stitches, press c ("Reverse/Reinforcement Stitch"
  • Brother International NX570Q | Operation Manual - Page 57
    After 3 to 5 reverse stitches have been sewn, g release ("Reverse/Reinforcement Stitch" button). X The machine stops sewing. Press ("Start/Stop" button), or press down h on the foot controller. At this time, if ("Start/Stop" button) is held down, the machine sews at a slow speed. Cutting
  • Brother International NX570Q | Operation Manual - Page 58
    SEWING BASICS Using the manual thread cutter When sewing with nylon or metallic threads, or other special threads, use the thread cutter on the side of the machine to cut
  • Brother International NX570Q | Operation Manual - Page 59
    Adjusting the Thread Tension The tensions of the upper thread and of the bobbin thread (thread tension) should be adjusted so that they are equal. Changing the tension of the upper thread Turn the thread tension dial to the left to loosen the upper thread. You may need to change the thread
  • Brother International NX570Q | Operation Manual - Page 60
    SEWING BASICS Adjusting the Stitch Width and Length The zigzag width (pattern width) and stitch length of utility stitches can be adjusted. Normally, when a stitch is selected, the appropriate width and length are automatically selected. For details on the range of values within which the width
  • Brother International NX570Q | Operation Manual - Page 61
    Adjusting the stitch length The stitch length can be adjusted to make the stitch longer or shorter. Turn on the sewing machine. a To make the stitch length shorter, press c (Stitch length key). To make the stitch length longer, press (Stitch length key). 2 X The stitch length is changed. X
  • Brother International NX570Q | Operation Manual - Page 62
    SEWING BASICS Useful Functions Functions useful in improving sewing efficiency are described below. Changing the needle stop position Automatically sewing reverse/ reinforcement stitches When the sewing machine is purchased, it is set to leave the needle lowered in the fabric when sewing is
  • Brother International NX570Q | Operation Manual - Page 63
    Press (Automatic reverse/reinforcement c stitch key). This step is not necessary if a stitch such as those for sewing buttonholes and bar tacks is selected where reinforcement stitches are automatically sewn. After reaching the end of the stitching, press e ("Reverse/Reinforcement Stitch"
  • Brother International NX570Q | Operation Manual - Page 64
    SEWING BASICS Automatically cutting the thread Position the fabric under the presser foot, and d then press ("Start/Stop" button) once. The sewing machine can be set to automatically cut the threads at the end of the stitching. This is called "programmed thread-cutting". If programmed
  • Brother International NX570Q | Operation Manual - Page 65
    be saved so that they will be specified each time the stitch is selected. The various settings can be saved for each utility stitch. Press (Manual memory key). b X "Saving..." appears while the settings for the stitch width and stitch length are being saved. X After the settings for the stitch
  • Brother International NX570Q | Operation Manual - Page 66
    SEWING BASICS Hands-free raising and lowering of the presser foot Using the knee lifter, you can raise and lower the presser foot with your knee, leaving both hands free to handle the fabric. ■ Using the knee lifter Stop the sewing machine. a • Do not use the knee lifter while the sewing machine
  • Brother International NX570Q | Operation Manual - Page 67
    Useful Sewing Tips Various ways to achieve better results for your sewing projects are described below. Refer to these tips when sewing your project. Trial sewing Sewing curves After you have set up the machine with the thread Stop sewing, and then slightly change the sewing and needle
  • Brother International NX570Q | Operation Manual - Page 68
    SEWING BASICS Sewing thick fabrics ■ If the fabric does not fit under the presser foot If the fabric does not fit easily under the presser foot, raise the presser foot lever even higher to bring the presser foot to its highest position. Release the presser foot locking pin (black d button). X
  • Brother International NX570Q | Operation Manual - Page 69
    from the edge of the fabric. 1 a Seam b Presser foot c Centimeters d Inches e Needle plate f 16 mm (5/8 inch) 2 a Seam b Presser foot ■ Aligning the fabric with the stitch guide foot Sew while keeping the right edge of the fabric aligned with a desired position of markings on the stitch
  • Brother International NX570Q | Operation Manual - Page 70
    SEWING BASICS Sewing hook-and-loop fastener CAUTION ● Use only the ungummed hook-and-loop fastener which is for sewing. If the glue is attached to the needle or the bobbin hook race, it may cause malfunction. ● If the hook-and-loop fastener is sewn with the thin needle (65/9-75/11), the needle may
  • Brother International NX570Q | Operation Manual - Page 71
    3 UTILITY STITCHES The various stitches and their applications are described in this chapter. Selecting Stitching 70 Selecting stitch types and patterns....... 70 Selecting stitching 72 Overcasting Stitches 76 Sewing overcasting stitches using overcasting foot "G 76 Sewing overcasting stitches
  • Brother International NX570Q | Operation Manual - Page 72
    UTILITY STITCHES Selecting Stitching You can select any of the various types of stitching available. Selecting stitch types and patterns A stitch can be selected from the following types available. Stitch patterns can be selected through either direct select (by pressing the key for a specific
  • Brother International NX570Q | Operation Manual - Page 73
    † Decorative stitches There are two decorative stitch modes: decorative stitch 1 mode and decorative stitch 2 mode . If (Decorative stitch key) is pressed once, decorative stitch 1 mode is selected. If (Decorative stitch key) is pressed twice, decorative stitch 2 mode is selected. Each press
  • Brother International NX570Q | Operation Manual - Page 74
    UTILITY STITCHES Selecting stitching Using the operation panel keys, select the desired stitch. Ten of the most often used utility stitches can quickly be selected with the numeric keys. Right after turning the power on, the straight stitch (left needle position) is selected. The machine can also
  • Brother International NX570Q | Operation Manual - Page 75
    ■ With number selection There are three modes of stitches that can be selected by number: utility stitch mode , decorative stitch mode and character stitch mode . In addition, there are two decorative stitch modes : decorative stitch 1 mode and decorative stitch 2 mode . There are three
  • Brother International NX570Q | Operation Manual - Page 76
    UTILITY STITCHES Use the numeric keys to type in the two-digit b number for the desired stitch. For stitches 01 through 09, the stitch can also be selected by using the numeric keys to type in a one-digit number, then pressing (OK key). X After the entered number appears in the center of the
  • Brother International NX570Q | Operation Manual - Page 77
    • To erase the stitch and select a different one, press (OK key), and then change the stitch mode. • To stop the current stitch from being erased, press (Cancel/clear key) to return to the previous screen. Memo z After changing stitch settings such as the stitch length and width or after
  • Brother International NX570Q | Operation Manual - Page 78
    Manual 2.0 1.0-4.0 (1/16) (1/16-3/16) 2.5 1.0-4.0 (3/32) (1/16-3/16) 2.5 1.0-4.0 (3/32) (1/16-3/16) Presser Foot G Attach overcasting foot "G". a G Sew with the edge of the fabric against the d presser foot guide the edge of the fabric c against the guide of the presser foot, and then lower the
  • Brother International NX570Q | Operation Manual - Page 79
    be used to sew overcasting stitches with zigzag foot "J". Pattern Numeric Stitch Name Key Application Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot Zigzag stitch (center 07 needle position) Preventing fraying (center baseline/ reverse stitching
  • Brother International NX570Q | Operation Manual - Page 80
    needle clamp screw. a Remove the presser foot. a • For details, refer to "Replacing the presser foot" (page 41). Lower the presser foot lever, and then b manually thread the needle. • The needle threader cannot be used. If the needle threader is used with the side cutter, the sewing machine may be
  • Brother International NX570Q | Operation Manual - Page 81
    fabric in the side cutter. j The cut in the fabric should be positioned over the guide plate of the side cutter. a a Guide plate • If the fabric is not positioned correctly, the fabric will not be cut. . z The optional side cutter is available through your brother dealer. Overcasting Stitches 79
  • Brother International NX570Q | Operation Manual - Page 82
    . Five stitches are available for basic stitching. Pattern Numeric Stitch Name Key Application Stitch Width [mm (inch)] Auto Manual 06 Basting stitch - Temporarily securing 0.0 (0) 0.0-7.0 (0-1/4) 01 Straight stitch (left needle position) 02 Straight stitch (center 03 needle position
  • Brother International NX570Q | Operation Manual - Page 83
    Basic stitching Baste or pin together the fabric pieces. a Attach zigzag foot "J". b J ■ Changing the needle position The needle position used as the baseline is different for the straight stitch (left needle position) and the straight stitch (center needle position). 1 2 • For details,
  • Brother International NX570Q | Operation Manual - Page 84
    Stitch Width [mm (inch)] Auto Manual 00 (0) 3← - 3→ 00 (0) 3← - 3→ Stitch Length [mm (inch)] Auto Manual 2.0 1.0-3.5 (1/16) (1/16-1/8) Position the fabric with the edge of the folded e hem against the guide of the presser foot, and then lower the presser foot lever. 1 3 2 a Wrong side
  • Brother International NX570Q | Operation Manual - Page 85
    stitch width so that the needle slightly catches the fold of the hem. Sew with the fold of the hem against the g presser foot guide. Remove the basting stitching. h 1 2 a Wrong side of fabric b Right side of fabric Memo z For best results when sewing stretch fabrics, decrease the pressure of
  • Brother International NX570Q | Operation Manual - Page 86
    5.0 3.0-5.0 (3/16) (1/8-3/16) 5.0 3.0-5.0 (3/16) (1/8-3/16) 5.0 3.0-5.0 (3/16) (1/8-3/16) 5.0 3.0-5.0 (3/16) (1/8-3/16) Stitch Length [mm (inch)] Auto Manual 0.4 0.2-1.0 (1/64) (1/64-1/16) 0.4 0.2-1.0 (1/64) (1/64-1/16) 0.4 0.2-1.0 (1/64) (1/64-1/16) 0.4 0.2-1.0 (1/64) (1/64-1/16) Presser Foot
  • Brother International NX570Q | Operation Manual - Page 87
    used for sewing buttonholes, are indicated below. Use chalk to mark on the fabric the position a and length of the buttonhole. 2 1 1 2 5 3 4 A a Button guide plate b Presser foot scale c Pin d Marks on buttonhole foot e 5 mm (3/16 inch) a Marks on fabric b Button hole sewing Pull out the button
  • Brother International NX570Q | Operation Manual - Page 88
    + thickness of button) c 5 mm (3/16 inch) Example: For a button with a diameter of 15 mm (9/16 inch) and a thickness of 10 mm (3/8 inch), the button guide plate should be set to 25 mm (1 inch) on the scale. 1 A 2 a Mark on fabric b Red marks on buttonhole foot Pass the upper thread down through
  • Brother International NX570Q | Operation Manual - Page 89
    ) to raise the needle, raise the presser foot, and then pull out the fabric before cutting the threads. For details, refer to "Using the manual thread cutter" (page 56). CAUTION ● When opening the buttonhole with the seam ripper, do not place your hands in the cutting direction, otherwise injuries
  • Brother International NX570Q | Operation Manual - Page 90
    UTILITY STITCHES ■ Changing the stitch width Adjust the stitch width. - + Attach buttonhole foot "A". b • For details, refer to "Replacing the presser foot" (page 41). Select stitch 52 or 53 . c Adjust the stitch width to the thickness of the d gimp thread. Lower the presser foot lever and
  • Brother International NX570Q | Operation Manual - Page 91
    Button sewing Buttons can be sewn on with the sewing machine. Buttons with 2 or with 4 holes can be attached. Measure the distance between the holes in the a button to be attached. Adjust the stitch width so that it is the same as e the distance between the holes in the button. Place the button
  • Brother International NX570Q | Operation Manual - Page 92
    UTILITY STITCHES Start sewing. h Set the sewing speed controller to the left (so that the speed will be slow). ■ Attaching a shank to a button To sew the button with a shank, attach the button with space between it and the fabric, and then wind the thread by hand. This attaches the button
  • Brother International NX570Q | Operation Manual - Page 93
    03 needle position) Attaching zippers Sewing concealed seams and pintucks Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot 3.5 0.0-7.0 2.5 0.2-5.0 I (1/8) (0-1/4) (3/32) (1/64-3/16) There are many methods for inserting zippers. The procedures for
  • Brother International NX570Q | Operation Manual - Page 94
    UTILITY STITCHES Attach the presser foot holder to the right pin e of zipper foot "I". 1 I 2 Topstitch around the zipper. g 1 3 2 a Pin on the right side b Needle drop point • For details, refer to "Replacing the presser foot" (page 41). Select stitch 03 . f • For details, refer to "
  • Brother International NX570Q | Operation Manual - Page 95
    Inserting a side zipper Press open the seam allowance from the c wrong side of the fabric. Stitching is sewn on only one piece of fabric. Use this type of zipper application for side openings and back 1 openings. 1 2 a Wrong side of fabric Press the seam allowance so that the right side d
  • Brother International NX570Q | Operation Manual - Page 96
    UTILITY STITCHES Select stitch 03 . g • For details, refer to "Selecting stitching" (page 72). Close the zipper, turn over the fabric, and then j baste the other side of the zipper to the fabric. CAUTION ● When using zipper foot "I", be sure to select the straight stitch (center needle position
  • Brother International NX570Q | Operation Manual - Page 97
    When you are about 5 cm (2 inches) from the m end of the zipper, stop the sewing machine with the needle lowered (in the fabric), raise the presser foot lever, and then open the zipper and continue sewing. Remove the basting stitching. n 3 Zipper Insertion 95
  • Brother International NX570Q | Operation Manual - Page 98
    stitch 01 (left needle position) Attaching zippers Sewing concealed seams and piping Stitch Width [mm (inch)] Auto Manual 0.0 0.0-7.0 (0) (0-1/4) Stitch Length [mm (inch)] Auto Manual Presser Foot 2.5 0.2-5.0 (3/32) (1/64-3/16) There are many methods for inserting zippers and pipings. The
  • Brother International NX570Q | Operation Manual - Page 99
    Securely tighten the positioning screw with a g screwdriver. Inserting a piping Place the piping between two fabric pieces 1 a turned inside out, as shown below. 1 2 a Positioning screw Topstitch around the zipper. h 1 3 2 3 a Fabric b Piping c Fabric Refer to the steps of attaching
  • Brother International NX570Q | Operation Manual - Page 100
    stitch Stretch fabrics - Attaching elastic - Attaching elastic to stretch fabrics Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot 1.0 1.0-3.0 2.5 1.0-4.0 (1/16) (1/16-1/8) (3/32) (1/16-3/16) 5.0 1.5-7.0 1.0 0.2-4.0 (3/16) (1/16-1/4) (1/16) (1/64-3/16
  • Brother International NX570Q | Operation Manual - Page 101
    Attach zigzag foot "J". b J • For details, refer to "Replacing the presser foot" (page 41). Select a stitch. c • For details, refer to "Selecting stitching" (page 72). Sew the elastic tape to the fabric while d stretching the tape so that it is the same length as the fabric. While pulling the
  • Brother International NX570Q | Operation Manual - Page 102
    ) Appliqué quilting, - free-motion quilting, satin stitching Stitch Width [mm (inch)] Auto Manual 3.5 0.0-7.0 (1/8) (0-1/4) 3.5 0.0-7.0 (1/8) (0-1/4) Stitch Length [mm (inch)] Auto Manual 1.4 0.0-4.0 (1/16) (0-3/16) 1.4 0.0-4.0 (1/16) (0-3/16) Presser Foot 19 Appliqué stitch 25 - Attaching
  • Brother International NX570Q | Operation Manual - Page 103
    Appliqué stitching Attach the open toe foot. d For best results, use the included open toe foot. Cut out the appliqué, leaving a seam a allowance of between 3 and 5 mm (1/8 and 3/16 inch). • For details, refer to "Replacing the presser foot" (page 41). 1 Select a stitch. e • For details,
  • Brother International NX570Q | Operation Manual - Page 104
    UTILITY STITCHES Patchwork (crazy quilt) stitching Fold the edge of the top piece of fabric and a place it over the lower piece. Sew the two pieces of fabric together so the b pattern spans over both pieces. Piecing Sewing together two pieces of fabric is called "piecing". The fabric pieces
  • Brother International NX570Q | Operation Manual - Page 105
    top and bottom layers of fabric is called "quilting". Quilts can easily be sewn using the walking foot and the optional quilting guide. Note z Thread the needle manually when using the walking foot, or only attach the walking foot after threading the needle using the needle threader. z When sewing
  • Brother International NX570Q | Operation Manual - Page 106
    over the needle clamp screw. 1 2 3 Note z The optional quilting guide is available through your dealer. Free-motion quilting With free-motion quilting, the screwdriver in your left hand. 1 Note z Thread the needle manually when using the quilting foot, or only attach the quilting foot after
  • Brother International NX570Q | Operation Manual - Page 107
    Slide the drop feed lever, located at the rear of d the machine on the base, to (to the left as seen from the rear of the machine). Satin stitching using the sewing speed controller A decorative stitch can be sewn by changing the stitch width of a satin stitch. If the sewing machine is
  • Brother International NX570Q | Operation Manual - Page 108
    UTILITY STITCHES Press or e . To return to width keys). (Stitch width keys) to select , press or (Stitch Memo z When the foot controller is plugged in, ("Start/Stop" button) cannot be used to start sewing. When you are finished sewing, set the stitch i width control setting back to OFF. X
  • Brother International NX570Q | Operation Manual - Page 109
    Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot Triple stretch 04 stitch sew" (page 52). Determine the desired length of the bar tack. a Set the button guide plate on buttonhole foot "A" to the desired length. (The distance between the markings on the
  • Brother International NX570Q | Operation Manual - Page 110
    UTILITY STITCHES Attach buttonhole foot "A". b • For details, refer to "Replacing the presser foot" (page 41). Pull down the buttonhole lever as far as e possible. Select stitch 60 . c • For details, refer to "Selecting stitching" (page 72). Position the fabric so that the opening of the d
  • Brother International NX570Q | Operation Manual - Page 111
    that has been torn can be darned. Darning is sewn as shown below. 1 a Reinforcement stitching 3 1 Determine the desired length of the darning. a Set the button guide plate on buttonhole foot "A" to the desired length. (The distance between the markings on the presser foot scale is 5 mm (3/16 inch
  • Brother International NX570Q | Operation Manual - Page 112
    UTILITY STITCHES Pull down the buttonhole lever as far as e possible. a a Buttonhole lever The buttonhole lever is positioned behind the bracket on the buttonhole foot. 1 2 a Buttonhole lever b Bracket Gently hold the end of the upper thread in f your left hand, and then start sewing. X Once sewing
  • Brother International NX570Q | Operation Manual - Page 113
    62 Eyelet stitch Sewing eyelets, for example, on belts Stitch Width [mm (inch)] Auto Manual 7.0, 6.0 or 7.0 5.0 (1/4) (1/4, 15/64 or 3/16) Stitch Length [mm (inch)] Auto Manual - - Presser Foot N Attach monogramming foot "N". a Start sewing. e X Once sewing is completed, the machine
  • Brother International NX570Q | Operation Manual - Page 114
    two pieces of fabric together across an open seam Stitch Width [mm (inch)] Auto Manual 5.0 0.0-7.0 (3/16) (0-1/4) Stitch Length [mm (inch)] Auto Manual Presser Foot 2.5 1.0-4.0 (3/32) (1/16-3/16) 5.0 2.5-7.0 2.5 1.0-4.0 (3/16) (3/25-1/4) (3/32) (1/16-3/16) 28 4.0 0.0-7.0 1.2 0.2-4.0 (3/16
  • Brother International NX570Q | Operation Manual - Page 115
    Rick-rack 36 stitch Decorative 37 stitch Serpentine 38 stitch Decorative stitching Stitch Width [mm (inch)] Auto Manual Stitch Length [mm (inch)] Auto Manual Presser Foot 6.0 1.5-7.0 1.6 1.0-4.0 (15/64) (1/16-1/4) (1/16) (1/16-3/16) N 5.0 1.5-7.0 1.6 1.0-4.0 (3/16) (1/16-1/4) (1/16) (1/16-3/16
  • Brother International NX570Q | Operation Manual - Page 116
    UTILITY STITCHES Scallop stitching The wave-shaped repeating pattern that looks like shells is called "scalloping". It is used on the collars of blouses and to decorate the edges of handkerchiefs. Attach monogramming foot "N". a Smocking The decorative stitch created by stitching or embroidering
  • Brother International NX570Q | Operation Manual - Page 117
    Select stitch 31 , 32 e or 33 . • For details, refer to "Selecting stitching" (page 72). Stitch between the straight stitches. f Select stitch 20 c thread tension. , and then increase the • For details, refer to "Selecting stitching" (page 72). Sew while making sure that the needle drops
  • Brother International NX570Q | Operation Manual - Page 118
    refer to "Replacing the needle" (page 39). • The needle threader cannot be used with the wing needle, otherwise the sewing machine may be damaged. Manually pass the thread through the eye of the needle from the front to the back. Attach monogramming foot "N". b • For details, refer to "Replacing the
  • Brother International NX570Q | Operation Manual - Page 119
    Start sewing. d Select stitch 39 . c • For details, refer to "Selecting stitching" (page 72). CAUTION ● Select a stitch width of 6.0 mm (15/64 With the right side of the fabric facing up, sew d along the right edge of the frayed section. inch) or less, otherwise the needle may bend or
  • Brother International NX570Q | Operation Manual - Page 120
    UTILITY STITCHES Press or g. To return to width keys). (Stitch width keys) to select , press or (Stitch ■ Drawnwork (Example 2) X The pattern is flipped. Pull out several threads from two sections of a the fabric, separated by an unfrayed section of about 4 mm (3/16 inch). Press h key). (OK
  • Brother International NX570Q | Operation Manual - Page 121
    desired result may not be achieved. Be sure to sew a trial piece of fabric before sewing your project. In addition, while sewing, be sure to guide the fabric with your hands in order to prevent the fabric from slipping. • The stitching is sewn in the direction indicated by the arrow. Sew
  • Brother International NX570Q | Operation Manual - Page 122
    UTILITY STITCHES Combining patterns Repeat steps b . c Multiple patterns can be combined and sewn together. Decorative stitches and character stitches (stitches selected with and ) can be combined. However, utility stitches (stitches selected with and ) cannot be combined. After all of
  • Brother International NX570Q | Operation Manual - Page 123
    Repeat sewing patterns To repeatedly sew the combined pattern, follow the procedure described below. Select the pattern. a • For details, refer to "Combining patterns" (page 120). Press b panel. (Settings key) in the operation X The settings screen appears. Press e key). (OK key) or (
  • Brother International NX570Q | Operation Manual - Page 124
    UTILITY STITCHES Press or (Stitch length keys) until b is displayed. Changing the pattern size X The screen for checking the pattern appears. The size of character stitches in the Gothic font ( selected with ) and outline style ( selected with ) can be switched between large and small. However
  • Brother International NX570Q | Operation Manual - Page 125
    Press or (Stitch width keys) until the d desired size is selected. Select for the small size or select for the large size. Changing the stitch density If a decorative satin stitch has been selected, the stitch density can be changed. Select a decorative satin stitch (No. 53-62 of a ,
  • Brother International NX570Q | Operation Manual - Page 126
    UTILITY STITCHES Press or (Stitch width keys) until the d desired density is selected. Select for sparse stitching or select for compact stitching. Press or (Stitch length keys) until c is displayed. X The screen for changing the length of a satin stitch appears. Press (OK key) or (Cancel/
  • Brother International NX570Q | Operation Manual - Page 127
    Mirror imaging the pattern The pattern can be mirror imaged along a vertical axis. Select a stitch. a Press b panel. (Settings key) in the operation X The settings screen appears. Press e key). (OK key) or (Cancel/clear X The initial stitch screen appears again. 1 2 a Normal b Mirror
  • Brother International NX570Q | Operation Manual - Page 128
    UTILITY STITCHES Saving patterns Combined patterns can be saved for later use. Since saved patterns are not lost after the sewing machine is turned off, they can be retrieved at any time. This is convenient for patterns, such as names, that will be used often. Utility stitches can also be saved.
  • Brother International NX570Q | Operation Manual - Page 129
    Press the numeric key (0 through 9) for the b pocket where the pattern is saved. X The saved contents of the pocket for the selected number are retrieved. Start sewing. c X The pattern for making the adjustment is sewn. X The sewing machine stops after it has • If nothing was saved in the
  • Brother International NX570Q | Operation Manual - Page 130
    UTILITY STITCHES Press or (Stitch width keys). g X Make the necessary adjustments according to how the pattern is sewn. Press (Stitch width key) to increase the adjustment setting. Press (Stitch width key) to decrease the adjustment setting. Start sewing again, and then check the pattern. h
  • Brother International NX570Q | Operation Manual - Page 131
    Designing a Pattern With the My Custom Stitch function, you can sew stitch patterns that you design yourself. Drawing a sketch of the pattern Prepare a grid sheet set. Mark the points in the pattern that are c positioned at intersections in the grid, and then link those points with a
  • Brother International NX570Q | Operation Manual - Page 132
    UTILITY STITCHES Entering the pattern data Follow the pattern drawn on the grid sheet and program the pattern into the sewing machine. Attach monogramming foot "N". a Check the grid sheet set, and specify the d coordinates of the first point. Press and (Stitch width keys) to select the
  • Brother International NX570Q | Operation Manual - Page 133
    Select g , and then press (OK key). Specify the various stitching settings, such as j reverse/reinforcement stitching, in the same way as with other stitches. • If you make a mistake while specifying a point, press (Cancel/clear key) so that the point changes from to , and then move (
  • Brother International NX570Q | Operation Manual - Page 134
    UTILITY STITCHES Examples of designs Enter each of the points indicated in the table to sew the sample stitch. Point Point 0 0 0 20 38 13 1 12 0 21 35 14 2 18 3 22 32 13 3 22 6 23 30 10 4 23 10 24 32 6 5 21 13 25 35 3 6 17 14 26 41 0 7 14 13 27 45
  • Brother International NX570Q | Operation Manual - Page 135
    stitches 138 Care and Maintenance 142 Restrictions on oiling 142 Cleaning the machine surface 142 Cleaning the race 142 Troubleshooting ...144 Frequent troubleshooting topics 144 Upper thread tightened up 144 Tangled thread on wrong side of fabric 145 Incorrect thread tension 147 Fabric
  • Brother International NX570Q | Operation Manual - Page 136
    stitch 14 15 134 Pattern Presser Foot Application Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual Reverse/ Reinforcement Stitching Programmed Thread-Cutting J Basic stitching, sewing gathers or pintucks, etc. 0.0 (0) 0.0-7.0 2.5 0.2-5.0 Yes (0-1/4) (3/32) (1/64
  • Brother International NX570Q | Operation Manual - Page 137
    Pattern Presser Foot Twin Needle Walking Foot Stitch Name Application Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual Reverse/ Reinforcement Stitching Programmed Thread-Cutting Overcasting 16 stitch 17 Blind hem stitch 18 Overcasting on stretch J fabrics and
  • Brother International NX570Q | Operation Manual - Page 138
    44 45 46 47 48 Buttonhole stitch 49 Application Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual Reverse/ Reinforcement Stitching Programmed Thread-Cutting J Fagoting and decorative stitching 5.0 (3/16) 0.0-7.0 (0-1/4) 2.5 (3/32) 1.0-4.0 Yes (1/16-3/16
  • Brother International NX570Q | Operation Manual - Page 139
    Presser Foot Twin Needle Walking Foot Stitch Name Application Stitch Width [mm (inch)] Stitch Length [mm (inch)] Auto Manual Auto Manual Reverse/ Reinforcement Stitching Programmed Thread-Cutting 50 51 52 53 Buttonhole stitch 54 A Horizontal buttonholes on thick fabrics 5.0 (3/16
  • Brother International NX570Q | Operation Manual - Page 140
    APPENDIX Other stitches Presser Foot Twin Needle Pattern Size Adjustable Stitching Density Adjustable Pattern Length/width Left/Right Flipping Stitch Type Pattern 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 Decorative stitches 21 22 23 24 25 26 27 28 29 30 N No Large No
  • Brother International NX570Q | Operation Manual - Page 141
    Presser Foot Twin Needle Pattern Size Adjustable Stitching Density Adjustable Pattern Length/width Left/Right Flipping Stitch Type Pattern 01 02 03 04 05 06 07 11 12 13 16 17 18* 20 21 22 23 24 25 26 Yes J** (*Not possible) Yes (J) 27* 28 29 Utility 08 09 10 decorative stitches 14 15
  • Brother International NX570Q | Operation Manual - Page 142
    Presser Foot Twin Needle Pattern Size Adjustable Stitching Density Adjustable Pattern Length/width Left/Right Flipping APPENDIX Stitch Type Pattern 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Character stitches (Gothic font) 31 32 33 34 35 36 37
  • Brother International NX570Q | Operation Manual - Page 143
    Presser Foot Twin Needle Pattern Size Adjustable Stitching Density Adjustable Pattern Length/width Left/Right Flipping Stitch Type Pattern 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 Character 21 22 23 24 25 26 27 28 29 30 stitches (Outline 31 32 33 34 35 36 37 38 39 40
  • Brother International NX570Q | Operation Manual - Page 144
    applied to ensure correct operation, making periodic oiling unnecessary. If problems occur, such as difficulty turning the handwheel or an unusual noise the machine, and contact you authorized dealer or the nearest authorized service center. Remove the flat bed attachment. c Remove the needle plate
  • Brother International NX570Q | Operation Manual - Page 145
    thread may become tangled, the needle may break or sewing performance may suffer. For a new bobbin case (part code: XC3153-321), contact your nearest authorized service center. ● Be sure that the bobbin case is correctly installed, otherwise the needle may break. Care and Maintenance 143
  • Brother International NX570Q | Operation Manual - Page 146
    you need additional help, the Brother Solutions Center offers the latest FAQs and troubleshooting tips. Visit us at " http://solutions.brother.com " . If the problem persists, contact your dealer or the nearest authorized service center. Frequent troubleshooting topics Detailed causes and remedies
  • Brother International NX570Q | Operation Manual - Page 147
    , refer to "Installing the bobbin" (page 26) and "Remedy/check details" in the section "Upper thread tightened up" (page 144) to correctly install the bobbin. Troubleshooting 145
  • Brother International NX570Q | Operation Manual - Page 148
    be threaded correctly. Press ("Needle Position" button) once or e twice to raise the needle. a Thread guide plate While using your right hand to lightly hold the h thread passed under the thread guide plate, pass the thread through the thread path in the order shown below. 1 1 a "Needle Position
  • Brother International NX570Q | Operation Manual - Page 149
    thread is visible from the lower side of the fabric. Turn the thread tension dial to a higher number (toward the right). (Tighten the thread tension.) Troubleshooting 147
  • Brother International NX570Q | Operation Manual - Page 150
    . If the operation could not be completed according to the procedure, instead of attempting to complete it forcefully, contact your nearest authorized service center. ■ Removing the fabric from the machine Immediately stop the sewing machine. a Turn off the sewing machine. b Remove the needle. c If
  • Brother International NX570Q | Operation Manual - Page 151
    If the fabric cannot be removed, even after completing these steps, contact your nearest authorized service center. Remove any threads in the race and around l the feed dogs. Turn the case • Make sure that the indicated points are aligned before installing the bobbin case. Troubleshooting 149
  • Brother International NX570Q | Operation Manual - Page 152
    tangled, the needle may break or sewing performance may suffer. For a new bobbin case (part code: XC3153-321), contact your nearest authorized service center. ● Make sure that you fit the bobbin case properly, otherwise the needle may break. Slowly turn the handwheel toward you c (counterclockwise
  • Brother International NX570Q | Operation Manual - Page 153
    the foot controller. passed under the pretension disk of the bobbin- winding thread guide correctly, the thread may become tangled under the bobbin winder seat. In such Cut the thread with scissors beside the bobbinb winding thread guide. 1 a Bobbin-winding thread guide Troubleshooting 151
  • Brother International NX570Q | Operation Manual - Page 154
    right hand as shown below. Wind the bobbin again. e Note z Make sure that the thread passes under the pretension disk of the bobbin-winding thread guide correctly (page 24). 152
  • Brother International NX570Q | Operation Manual - Page 155
    spool is incorrectly installed. Lightly guide the fabric. Correctly install the nearest - burr on it. authorized service center. The area around the hole burr on it. authorized service center. The bobbin case is scratched, dealer or the nearest authorized service center. - A bobbin
  • Brother International NX570Q | Operation Manual - Page 156
    used, or the thread has come out of the needle bar thread guide). Correct the upper threading. There are knots or tangles in the thread on it. Replace the needle plate. Contact your dealer or the nearest authorized service center. The area around the hole in the presser foot is scratched, or
  • Brother International NX570Q | Operation Manual - Page 157
    . page 39 Dust has accumulated under the Remove the needle plate cover needle plate or in the bobbin case. and clean the race. page 142 Troubleshooting 155
  • Brother International NX570Q | Operation Manual - Page 158
    the presser foot level while sewing. The sewing lamp does not come on. The sewing lamp is damaged. Contact your dealer or the nearest authorized service center. Nothing appears in The brightness of the LCD is either the LCD. too light or too dark. Adjust the brightness of the LCD. Reference
  • Brother International NX570Q | Operation Manual - Page 159
    through the bobbin-winding thread guide correctly. Correctly pass the thread through the bobbin-winding thread guide. page 24 Bobbin thread does is damaged. direction. Contact your dealer or the nearest authorized service center. - 4 The upper thread The bobbin thread is Troubleshooting 157
  • Brother International NX570Q | Operation Manual - Page 160
    up or if an operation is performed incorrectly, an error message appears in the LCD. Follow the instructions that appear. The message will disappear if (OK key) or (Cancel/clear key) is pressed while is being used, the machine may be malfunctioning. Contact your nearest authorized service center.
  • Brother International NX570Q | Operation Manual - Page 161
    . Be sure to check for the cause of the error, and correct it before continuing to sew. X The screen for changing the beep setting appears. Troubleshooting 159
  • Brother International NX570Q | Operation Manual - Page 162
    APPENDIX Press or d . To return to keys). (Stitch width keys) to select , press or (Stitch width X The machine is now set so that it will not beep. Press (Cancel/clear key) or (OK key). e X The initial stitch screen appears again. 160
  • Brother International NX570Q | Operation Manual - Page 163
    bobbin thread 26 pulling up 36 bobbin winder 10 bobbin winder shaft spring 23 bobbin winding thread guide and pretension disk .. 10, 24 , bobbin-winding 7 22 brightness 21 built-in stitches 9 heirloom stitching 116 I included accessories 8 Inserting a piping 97 Troubleshooting / Index 161
  • Brother International NX570Q | Operation Manual - Page 164
    7 26 M machine settings 19 , main power switch 11 17 maintenance 142 manual memory key 13 memory key 13 mirror image 125 monogramming foot 9 , My Custom Stitch 71 129 N needle 37 needle bar thread guide 11 needle clamp screw 40 needle mode selection key 13 , needle plate
  • Brother International NX570Q | Operation Manual - Page 165
    , thread cutter button 12 55 thread guide cover 10 thread guide disk 11 thread guide plate 10 thread tension 57 thread tension ajustment 57 , thread tension dial 10 57 top cover 10 4 trial sewing 65 triple stretch stitch 107 troubleshooting 144 twin needle 9, 33, 40 U upper
  • Brother International NX570Q | Operation Manual - Page 166
  • Brother International NX570Q | Operation Manual - Page 167
  • Brother International NX570Q | Operation Manual - Page 168
    Please visit us at http://solutions.brother.com where you can get product support and answers to frequently asked questions (FAQs). English 885-U22 Printed in China XE0403-2012
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
GETTING READY
SEWING BASICS
UTILITY STITCHES
APPENDIX
Read before use.
Read when additional
information is required.
Computerized Sewing Machine
Product Code: 885-U22
Operation Manual