Brother International PE500 Users Manual - English - Page 36

Installing the bobbin - needle size

Get Brother International PE500 PDF manuals and user guides View all Brother International PE500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

GETTING READY Cut the thread with scissors beside the bobbinb winding thread guide. Installing the bobbin a a Bobbin-winding thread guide Slide the bobbin winder shaft to the left, and c then remove the bobbin from the shaft. Install the bobbin wound with thread. CAUTION ● Use a bobbin that has been correctly wound with thread, otherwise the needle may break or the thread tension will be incorrect. Hold the thread end with your left hand, and d wind off the thread clockwise near the bobbin with your right hand as shown below. ● The included bobbin was designed specifically for this machine. If bobbins from other models are used, the machine will not operate correctly. Use only the included bobbin or bobbins of the same type (part code: SA156, SFB (XA5539151)). Actual size 11.5 mm (7/16 inch) This model Other model Memo z The order that the bobbin thread should be passed through the bobbin case is indicated by marks that surround the bobbin case. Wind the bobbin again. e Note z Make sure that the thread passes under the pretension disk of the bobbin-winding thread guide correctly (page 31). 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
34
GETTING READY
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
b
Cut the thread with scissors beside the bobbin-
winding thread guide.
a
Bobbin-winding thread guide
c
Slide the bobbin winder shaft to the left, and
then remove the bobbin from the shaft.
d
Hold the thread end with your left hand, and
wind off the thread clockwise near the bobbin
with your right hand as shown below.
e
Wind the bobbin again.
Note
Make sure that the thread passes under the
pretension disk of the bobbin-winding
thread guide correctly (page 31).
Installing the bobbin
Install the bobbin wound with thread.
CAUTION
Memo
The order that the bobbin thread should be
passed through the bobbin case is indicated
by marks that surround the bobbin case.
a
●
Use a bobbin that has been correctly
wound with thread, otherwise the needle
may break or the thread tension will be
incorrect.
●
The included bobbin was designed
specifically for this machine. If bobbins
from other models are used, the machine
will not operate correctly. Use only the
included bobbin or bobbins of the same
type (part code: SA156, SFB (XA5539-
151)).
This model
Other model
11.5 mm
(7/16 inch)
Actual size