Brother International PE770 Users Manual - English - Page 11

Needle and embroidery foot Right-side/rear view - threading

Get Brother International PE770 - Computerized Embroidery Machine PDF manuals and user guides
UPC - 012502623489
View all Brother International PE770 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Needle and embroidery foot section Right-side/rear view a Thread guide disk Pass the thread through the thread guide disk when using the needle threader to thread the needle. b Needle bar thread guide Pass the upper thread through the needle bar thread guide. c Needle plate When the needle is lowered, it enters the hole in the needle plate. d Needle plate cover Remove the needle plate cover to clean the bobbin case and race. e Bobbin cover/bobbin case Remove the bobbin cover, and then insert the bobbin into the bobbin case. f Embroidery foot "Q" This presser foot is used for embroidering. a Handle Carry the machine by its handle when transporting the machine. b Handwheel Turn the handwheel toward you (counterclockwise) to raise and lower the needle. c Embroidery card slot Insert the embroidery card. d Air vent The air vent allows the air surrounding the motor to be exchanged. Do not cover the air vent while the machine is being used. e Power supply jack Insert the plug on the power supply cord into the power supply jack. f Main power switch Use the main power switch to turn the machine on and off. Memo z Refer to pages 8 through 11 while you are learning to use your machine. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
9
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
Needle and embroidery foot section
a
Thread guide disk
Pass the thread through the thread guide disk when
using the needle threader to thread the needle.
b
Needle bar thread guide
Pass the upper thread through the needle bar thread
guide.
c
Needle plate
When the needle is lowered, it enters the hole in the
needle plate.
d
Needle plate cover
Remove the needle plate cover to clean the bobbin case
and race.
e
Bobbin cover/bobbin case
Remove the bobbin cover, and then insert the bobbin
into the bobbin case.
f
Embroidery foot “Q”
This presser foot is used for embroidering.
Right-side/rear view
a
Handle
Carry the machine by its handle when transporting the
machine.
b
Handwheel
Turn the handwheel toward you (counterclockwise) to
raise and lower the needle.
c
Embroidery card slot
Insert the embroidery card.
d
Air vent
The air vent allows the air surrounding the motor to be
exchanged. Do not cover the air vent while the
machine is being used.
e
Power supply jack
Insert the plug on the power supply cord into the power
supply jack.
f
Main power switch
Use the main power switch to turn the machine on and
off.
Memo
z
Refer to pages 8 through 11 while you are
learning to use your machine.