Brother International PE770 Users Manual - English - Page 29

thread using the cutter built into the slit - not cutting thread

Get Brother International PE770 - Computerized Embroidery Machine PDF manuals and user guides
UPC - 012502623489
View all Brother International PE770 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Pass the end of the thread through the guide l slit in the bobbin winder seat, and then pull the thread to the right to cut it. Use scissors to cut the end of the thread n wound around the bobbin. 1 1 a Guide slit in bobbin winder seat (with built-in cutter) CAUTION ● Be sure to cut the thread as described. If the bobbin is wound without cutting the thread using the cutter built into the slit in the bobbin winder seat, the thread may become tangled in the bobbin or the needle may bend or break when the bobbin thread starts to run out. Press (Start/stop button) once to start m winding the bobbin. Slide the bobbin winder shaft to the left, and o then remove the bobbin from the shaft. Remove the spool for the bobbin thread from p the spool pin, and then close the top cover. Memo z When the machine is started or the handwheel is turned after winding the bobbin, the machine will make a clicking sound; this is not a malfunction. 1 a Start/stop button • When the bobbin winding becomes slow, press (Start/stop button) once to stop the machine. CAUTION ● When the bobbin winding becomes slow, stop the machine, otherwise the machine may be damaged. Winding/Installing the Bobbin 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Winding/Installing the Bobbin
27
1
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
l
Pass the end of the thread through the guide
slit in the bobbin winder seat, and then pull
the thread to the right to cut it.
a
Guide slit in bobbin winder seat
(with built-in cutter)
CAUTION
m
Press
(Start/stop button) once to start
winding the bobbin.
a
Start/stop button
•
When the bobbin winding becomes slow,
press
(Start/stop button) once to stop the
machine.
CAUTION
n
Use scissors to cut the end of the thread
wound around the bobbin.
o
Slide the bobbin winder shaft to the left, and
then remove the bobbin from the shaft.
p
Remove the spool for the bobbin thread from
the spool pin, and then close the top cover.
Memo
z
When the machine is started or the
handwheel is turned after winding the
bobbin, the machine will make a clicking
sound; this is not a malfunction.
●
Be sure to cut the thread as described. If
the bobbin is wound without cutting the
thread using the cutter built into the slit
in the bobbin winder seat, the thread
may become tangled in the bobbin or the
needle may bend or break when the
bobbin thread starts to run out.
●
When the bobbin winding becomes slow,
stop the machine, otherwise the machine
may be damaged.
1
1