Canon 2677B002 SX80 Manual - Page 129

Replacing the Lamp, About the Replacing Lamp

Get Canon 2677B002 PDF manuals and user guides View all Canon 2677B002 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 129 highlights

Maintenance Replacing the Lamp When the time of use of the lamp exceeds the certain amount of time, the following message (two types) is displayed for 10 seconds every time the projector is turned on. 1,800 - less than 2,000 hours the OK button, and the POWER button are available during this message is displayed. (When you press the POWER button, "Push POWER button again to turn off the power." message appears.) • This message will not be displayed again if you select [Cancel] in response to the message "Do you want to display this message again?". Over 2,000 hours * The POWER button is available during this message is displayed. (When you press the POWER button, "Push POWER button again to turn off the power." message appears.) • After the above screens (two types) have been displayed for 10 seconds and disappeared, all buttons become operable. • You can check the time of use of the lamp in [Lamp counter] in the [System settings] menu (P98). ■About the Replacing Lamp This projector uses the following lamp. Lamp type No.RS-LP05 Caution • Be sure to use the specified lamp. • A lamp can be ordered from your dealer. • When replacing the lamp, turn off the projector, wait until the cooling fan stops, remove the power plug from the AC outlet, and let the projector stand for at least 1 hour. Otherwise, you may get burned because the main unit is very hot immediately after the projector is turned off. • Do not touch the inner glass surface when you replace the lamp. Otherwise, the projector 's performance may degrade. • Make sure to handle the lamp carefully and correctly since it may explode if it is scratched or shocked. If a lamp explodes, follow the instructions under "If a Lamp Explodes" on page 16. • Do not remove screws unless specified. Appendix 129

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
129
Maintenance
Appendix
Replacing the Lamp
When the time of use of the lamp exceeds the certain amount of time, the following mes-
sage (two types) is displayed for 10 seconds every time the projector is turned on.
1,800 - less than 2,000 hours
Over 2,000 hours
•
After the above screens (two types) have been displayed for 10 seconds and disap-
peared, all buttons become operable.
•
You can check the time of use of the lamp in [Lamp counter] in the [System settings]
menu (
P98
).
■
About the Replacing Lamp
This projector uses the following lamp.
Lamp type No.RS-LP05
•
This message will not be displayed again if you select [Cancel] in response to the mes-
sage "Do you want to display this message again?".
•
Be sure to use the specified lamp.
•
A lamp can be ordered from your dealer.
•
When replacing the lamp, turn off the projector, wait until the cooling fan stops, remove the
power plug from the AC outlet, and let the projector stand for at least 1 hour. Otherwise, you
may get burned because the main unit is very hot immediately after the projector is turned off.
•
Do not touch the inner glass surface when you replace the lamp. Otherwise, the projector 's
performance may degrade.
•
Make sure to handle the lamp carefully and correctly since it may explode if it is scratched or
shocked. If a lamp explodes, follow the instructions under "If a Lamp Explodes" on page
16
.
•
Do not remove screws unless specified.
*
[<] / [>], the
OK
button, and the
POWER
but-
ton are available during this message is dis-
played.
(When you press the
POWER
button, "Push
POWER button again to turn off the power."
message appears.)
* The
POWER
button is available during this
message is displayed.
(When you press the
POWER
button, "Push
POWER button again to turn off the power."
message appears.)
Caution