Home » Canon Manuals » Projectors » Canon 2677B002 » Manual Viewer

Canon 2677B002 SX80 Manual - Page 61

Turning Off the Projector

Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Projecting an Image Turning Off the Projector 1 Press the POWER button to pop up a window shown at the lower right. Remote control Top control Press the POWER button again while the confirmation message is displayed. The lamp goes off, the [POWER] indicator starts flashing in red and the cooling fan starts. • You cannot turn the projector on while the cooling fan is in operation. If you want to continue projecting, press a button other than POWER or wait until the confirmation message disappears. • You may shorten the lamp life if turning off the projector while its lamp is still in an unstable state shortly after turning on the projector. Wait at least 5 minutes before turning off the projector. It may shorten the lamp life if you turn on the projector immediately after turning it off. • Wait at least 5 minutes before turning on the projector when you turn off the projector. • Using the projector for a long time may shorten the life of the lamp and internal optical components. 2 Remove the power cord from the AC outlet. It continues to cool down the lamp even after removing the power cord. Thus, you may carry it immediately after the use. With the power cord connected, the LED illumination lamp turns on during cooling cycle. • Wait until the cooling fan stops before putting the projector in the carrying bag. Do not put the projector in the carrying bag until the cooling fan stops rotating. The projector may be damaged due to the heat. • Attach the lens cap to the lens to protect it and put the projector in the carrying bag. 61

Section	Page
To Start Menu	1
Features of SX80 Multimedia Projector	2
Major Features	2
Quick Reference Guide	4
Table of Contents	5
Safety Instructions	10
Safety Precautions	11
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.	12
AC Power Cord Requirement	14
Federal Communication Commission Notice	15
Canadian Radio Interference Regulations	15
Precautions on Handling the Batteries in the Remote Controller	16
Lamp Handling Precautions	16
Carrying/Transporting the Projector	17
Installation Precautions	17
Before Use	19
Supplied Accessories	20
Installing the Lens Cap	20
Putting the Projector in the Carrying Bag	21
Part Names	22
Main Unit of Projector	22
Front Side	22
Rear Side	22
Bottom Side	23
Remote Control	24
Top Control	26
Input Terminals	27
Preparing the Remote Control	28
Installing Remote Control Batteries	28
Remote Control Operating Range	28
Projecting an Image	29
Steps for Setting Up the Projector and Projecting an Image	30
Setting Up the Projector	31
Placing in Front of the Screen	31
Placing on a Level Place	32
When Pointing the Projector Up	33
Connecting the Projector	34
Connectable Equipment and Input Terminals	34
Connecting the Projector to the Computer	35
Connecting to RGB Monitor Output Terminal (analog connection)	35
Connecting to DVI Monitor Output Terminal (digital connection)	37
Connecting to AV Equipment	38
Connecting to Digital Video Output Terminal (digital connection)	38
Connecting to Analog Video Output Terminal (analog connection)	39
Connecting a Digital Camera or an USB Flash Memory	41
Starting Projection	42
When the Language Selection Screen Appears	43
When the Password Input Screen Appears	44
When \	44
When Notebook Computer Screen Does Not Appear	44
Adjusting Image	44
Changing Notebook Computer Screen Output	44
Turning On External Monitor Output	44
Setting Up the Screen Automatically	45
Auto Setup	45
Performing the Auto Setup	46
Selecting an Input Signal (INPUT)	47
Types of Input Signals	47
Selecting an Input Signal	48
Adjusting Image	49
Setting the Display Resolution of the Computer	49
Windows Vista	49
Windows XP	49
Macintosh OSX	49
AUTO PC	50
Performing the Auto PC Function	50
Adjusting the Image Size	51
Adjusting the Focus	52
Auto focusing	52
Manual focusing	52
Adjusting Keystone Distortion	53
Auto adjustment	53
Manual adjustment	53
Selecting Screen Aspect and Aspect	55
Selecting Screen Aspect	55
Moving Image with 16:9 D. Image Shift	57
Selecting Aspect Ratio	58
Types of Aspect Ratios	58
How to Select an Aspect Ratio	59
Selecting an Image Mode	60
Image modes	60
How to Select an Image Mode	60
Turning Off the Projector	61
Useful Functions Available During a Presentation	63
Blackened Out an Image Temporarily	64
Freezing the Picture	64
Adjusting the Volume	65
Muting the Sound	65
Zooming an Image	66
Showing the Elapsed Time	67
Projecting Image Without Computer	67
Setting Functions from Menus	69
How to Use Menus	70
Menu Configuration	70
Basic Operation of Menu	71
Setting Display Status	73
Selecting an Image Projection Mode	73
Selecting an Input Signal Type (ANALOG PC)	74
Selecting an Input Signal Type (VIDEO/S- VIDEO)	74
Selecting an Input Signal Type (COMPONENT)	75
Adjusting Input Signal (ANALOG PC) - Total Dots	75
Adjusting Input Signal (ANALOG PC) - Tracking	76
Adjust Input Signal (ANALOG PC) - Horizontal position	76
Adjust Input Signal (ANALOG PC) - Vertical position	77
Adjust Input Signal (ANALOG PC) - Horizontal pixels	77
Adjust Input Signal (ANALOG PC) - Vertical pixels	78
Selecting HDMI Input Level	78
Select HDMI Over Scan	79
Performing Progressive Processing	79
Selecting a Menu Position	80
Correcting the Screen Color	80
Reversing projection	81
Capturing a Logo	82
Selecting the User Logo Display Position	82
Displaying a User Logo (No signal screen)	83
Displaying a User Logo (BLANK)	83
Selecting a Logo at Startup	84
Selecting Aspect Ratio of Screen	84
Setting the Image Quality	85
Selecting an Image Quality	85
Adjusting the Brightness	86
Adjusting the Contrast	86
Adjusting the Sharpness	87
Making a Gamma Correction	87
Making Color Adjustment (HDMI/PC/USB)	88
Making Color Adjustment (COMPONENT/VIDEO/S-VIDEO)	88
Making Advanced Adjustment (Noise reduction)	89
Making Advanced Adjustment (Dynamic gamma)	89
Making Advanced Adjustment (Mem. color correct)	90
Adjusting Fine Color Adjustment (6-axis color adjust)	90
Reducing the Lamp Brightness	91
Resetting the Image Settings	91
Setting Various Function	92
Setting Auto Setup Function	92
Selecting the Power Management Mode	92
Skip the POWER Button Operation	93
Enabling/Disabling the Beep	93
Prohibiting the Projector Operation	94
Selecting a Display Language	94
Showing/hiding the Guide Screen	95
Turning on/off LED Illumination	95
Setting for Slideshow	96
Setting up the Remote Control Channel	96
Extending the Menu Display Time	97
Setting a Password	97
Registering a Password	98
Resetting the Lamp Counter	98
About the Display of the Lamp Counter	99
Initializing network settings	99
Resetting to the Default Setting	100
Checking the Information of the Projector	101
Projecting an Image from a Digital Camera or an USB Flash Memory	103
Projecting an Image from a Digital Camera	104
Connecting a Digital Camera	104
Operating the Projected Image	106
Switching to the Next Image	106
Rotating an Image	106
Running a Slideshow	107
Setting a Slideshow Interval	107
Finishing projection	107
Projecting Data on USB Flash Memory	108
Connecting an USB Flash Memory	108
Description of USB File Browser	110
Selecting an Image for Projection	111
Selecting a Drive	111
Selecting a Folder	111
Selecting an Image File for Projection	112
Operating the Projected Image	113
Switching to the Previous/Next Image	113
Rotating an Image	113
Returning to the USB File Browser	113
Running a Slideshow of Data saved in a USB Flash Memory	114
Creating an Image File Folder	114
Setting a Slideshow Interval	114
Connecting the Projector to Network	115
Setting an IP Address	116
Setting IP Address	116
If You Want to Reset the IP Address Setting	117
Setting Network	117
If You Want to Reset the Network Setting	119
Error Notification Message	119
Appendix	121
Troubleshooting	122
WARNING Lamp Flash Patterns	122
Symptoms and Solutions	123
You cannot turn on the projector.	123
You cannot project an image from the projector.	123
A digital camera or USB flash memory is not recognized.	124
You cannot hear sound.	124
The projected image is blur.	125
You cannot project an image appropriately.	125
The projector is forced to be turned off.	125
You cannot operate the remote control.	126
Maintenance	127
Cleaning the Projector	127
Cleaning and Replacing the Air Filter	128
Cleaning the Air Filter	128
Replacing the Air Filter	128
Replacing the Lamp	129
About the Replacing Lamp	129
Replacing the Lamp	130
Relationship between Aspect and Screen Aspect	131
When Projecting an Image from a Computer	131
When Projecting an Image from Image Software	132
When Projecting an Image from a Digital Camera or a USB Flash Memory	132
Supported Computer Signal Types	133
Relationship between Screen Size and Projecting Distance	134
Glossary	135
Specifications	139
Projector	139
Remote Control	139
External View	140
ANALOG PC-2/COMPONENT IN terminal	140
Service Port (CONTROL)	141
Index	142
Numerics	142
A	142
B	142
C	142
D	142
E	142
F	142
G	142
H	142
I	142
K	143
L	143
M	143
N	143
O	143
P	143
R	143
S	143
T	144
U	144
V	144
W	144
Z	144

Match case Limit results 1 per page

Projecting an Image

Turning Off the Projector

Press the POWER button to pop up a window shown at the lower right.

Press the

POWER

button again while the confirmation message is displayed.

The lamp goes off, the [POWER] indicator starts flashing in red and the cooling fan

starts.

Remove the power cord from the AC outlet.

It continues to cool down the lamp even after removing the power cord. Thus, you

may carry it immediately after the use.

With the power cord connected, the LED illumination lamp turns on during cooling

cycle.

•

You cannot turn the projector on while the cooling fan is in operation.

If you want to continue projecting, press a button other than

POWER

or wait until the con-

firmation message disappears.

•

You may shorten the lamp life if turning off the projector while its lamp is still in an unstable

state shortly after turning on the projector. Wait at least 5 minutes before turning off the pro-

jector. It may shorten the lamp life if you turn on the projector immediately after turning it off.

•

Wait at least 5 minutes before turning on the projector when you turn off the projector.

•

Using the projector for a long time may shorten the life of the lamp and internal optical

components.

•

Wait until the cooling fan stops before putting the projector in the carrying bag. Do not put

the projector in the carrying bag until the cooling fan stops rotating. The projector may be

damaged due to the heat.

•

Attach the lens cap to the lens to protect it and put the projector in the carrying bag.

Remote control

Top control