Canon DP-V1710 User Manual - Page 29

Place the universal measuring probe pointing at the center of the video display.

Get Canon DP-V1710 PDF manuals and user guides View all Canon DP-V1710 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Operating the Video Display 2 Select [User 1] to [User 7] and then open the [Calibration] menu. 1 [Adjustment] [Picture Mode] [User 1] to [User 7] 2 [Adjustment] [Detail Settings] [Calibration] • Set each target value. 3 Press the jog dial and select [Start]. 29 • Please follow the information indicated on the screen. 4 Initialize the sensor. • Set the mode dial of the Universal Measuring Probe to [0-CAL]. • Press the jog dial of the video display, select [OK], and execute initialization. 5 Place the universal measuring probe pointing at the center of the video display. • Set the mode dial of the universal measuring probe to [MEAS] and place the probe as shown below according to the displayed content. Press the jog dial of the video display, select [OK], and execute calibration. Main Unit Konica Minolta Universal Measuring Probe CA-310 support: CA-PU32, CA-PU35 CA-210 support: CA-PU12, CA-PU15 Konica Minolta Display Color Analyzer CA-310, CA-210 6 Finish calibration. • When the message [Calibration is completed]. is displayed, press the jog dial and select [OK]. • If the message [Calibration error.] is displayed. Calibration has been terminated due to an error. The main unit returns to the state before calibration. ( 99) • To cancel calibration Press the jog dial during calibration and select [Cancel]. The main unit returns to the state before calibration. Note • Perform matrix calibration of the display color analyzer prior to calibration. If calibration is performed without performing matrix calibration, an error may occur. Refer to the CA-310 and CA-210 instruction manual for the detail operation. • Warming-up is necessary to stabilize the brightness of the video display. Wait at least 10 minutes after turning on the power before calibration. • Perform calibration in a dark room so that no external light enters the sensor. If external light enters the sensor, low brightness characteristics cannot be calibrated correctly. • Due to the characteristic of LCD panel and individual difference of CA-310 and CA-210, the calibration results may differ.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
Operating the Video Display
29
2 Select [User 1] to [User 7] and then open the [Calibration] menu.
1
[Adjustment]
[Picture Mode]
[User 1] to [User 7]
2
[Adjustment]
[Detail Settings]
[Calibration]
•
Set each target value.
3 Press the jog dial and select [Start].
•
Please follow the information indicated on the screen.
4 Initialize the sensor.
•
Set the mode dial of the Universal Measuring Probe to [0-CAL].
•
Press the jog dial of the video display, select [OK], and execute initialization.
5 Place the universal measuring probe pointing at the center of the video display.
•
Set the mode dial of the universal measuring probe to [MEAS] and place the probe as shown below according to
the displayed content. Press the jog dial of the video display, select [OK], and execute calibration.
Konica Minolta Universal Measuring Probe
CA-310 support: CA-PU32, CA-PU35
CA-210 support: CA-PU12, CA-PU15
Konica Minolta
Display Color Analyzer CA-310, CA-210
Main Unit
6 Finish calibration.
•
When the message [Calibration is completed]. is displayed, press the jog dial and select [OK].
•
If the message [Calibration error.] is displayed.
Calibration has been terminated due to an error. The main unit returns to the state before calibration. (
99)
•
To cancel calibration
Press the jog dial during calibration and select [Cancel]. The main unit returns to the state before calibration.
Note
•
Perform matrix calibration of the display color analyzer prior to calibration. If calibration is performed without performing matrix
calibration, an error may occur. Refer to the CA-310 and CA-210 instruction manual for the detail operation.
•
Warming-up is necessary to stabilize the brightness of the video display. Wait at least 10 minutes after turning on the power before
calibration.
•
Perform calibration in a dark room so that no external light enters the sensor. If external light enters the sensor, low brightness
characteristics cannot be calibrated correctly.
•
Due to the characteristic of LCD panel and individual difference of CA-310 and CA-210, the calibration results may differ.