Canon DP-V1711 Video Display Operation Guide - Page 72

Around Peak, Luminance, Hybrid Log-Gamma except for Hybrid Log-Gamma RGB

Get Canon DP-V1711 PDF manuals and user guides View all Canon DP-V1711 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

OSD Menu Sub Menu Reset Position 72 Normal Around Peak Luminance Chromaticity Diagram On, Off Setting Options (Bold: factory default) Sets operation when the RESET button is pressed. [Normal]: Resets the value to the default value. [Around Peak Luminance]: Moves closer to the area of peak luminance inside the display image. Switches the chromaticity diagram On, Off. [On]: Displays the chromaticity diagram. The chromaticity diagram is displayed only when [Color Gamut] and [Gamma/EOTF] are set as shown below. ž [Color Gamut]: ITU-R BT.2020 ž [Gamma/EOTF]: 1.0, 2.2, 2.35, 2.4, 2.6, SMPTE ST 2084 (PQ), Hybrid Log-Gamma (except for Hybrid Log-Gamma RGB) • When the position to display [Wave Form Monitor] or [Vector Scope] is set to [Bottom Left], this item may not be displayed depending on the size setting for each item to be displayed. Test Pattern White (1023) White (940) Gray Black (64) Black (0) Ramp Color Bars Color Bars (PQ Full) Color Bars (PQ Limited) Color Bars (HLG) PLUGE PLUGE (PQ/HLG) Off Sets the test pattern built into the main unit. • If the power is turned off once and then back on, the test pattern will not be displayed. • The test pattern will be erased in the following cases: -- When a channel is changed using the CH button, F button assigned for Channel UP/Channel DOWN, or [Select Channel] under [Channel Settings] -- When changing [Input Configuration] or [Select Input Signal] under [Channel Settings] -- When [Reset All Settings] is executed Signal Monitoring Monitors the input signal status. • [Signal Monitoring] cannot be used in the following cases: -- When [Single Input Dual View] is displayed -- When an enlarged image is displayed -- During display of the test pattern -- During execution of [Playback File] under [Screen Capture] • When an error is displayed, [In Monitor Display] will not be shown. • The position the error is displayed can be adjusted with [In Monitor Display] [Position]. Control On, Off Sets whether [Signal Monitoring] is used or not. Error Hold On (No time out) On (5 sec.) Off Sets the length of time for displaying errors, when they are detected. [On (No time out)]: Errors continue to be displayed. To hide the displayed error, press the RESET button when closing the OSD menu. [On (5 sec.)]: The displayed error will disappear 5 seconds after the initial detection. [Off]: Only displays errors during the period when they are detected. The displayed error message will disappear once the error ends. No Signal/Unsupported On, Off Signal Displays an error when there is [No Signal] or [Unsupported Signal].

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
OSD Menu
72
Sub Menu
Setting Options (Bold: factory default)
Reset Position
Normal
Around Peak
Luminance
Sets operation when the RESET button is pressed.
[Normal]: Resets the value to the default value.
[Around Peak Luminance]: Moves closer to the area of peak luminance
inside the display image.
Chromaticity Diagram
On
, Off
Switches the chromaticity diagram On, Off.
[
On]: Displays the chromaticity diagram. The chromaticity diagram is
displayed only when [Color Gamut] and [Gamma/EOTF] are set as
shown below.
²
[Color Gamut]: ITU-R BT.2020
²
[Gamma/EOTF]: 1.0, 2.2, 2.35, 2.4, 2.6, SMPTE ST 2084 (PQ),
Hybrid Log-Gamma (except for Hybrid Log-Gamma RGB)
• When the position to display [Wave Form Monitor] or [Vector Scope] is set to
[Bottom Left], this item may not be displayed depending on the size setting for
each item to be displayed.
Test Pattern
White (1023)
White (940)
Gray
Black (64)
Black (0)
Ramp
Color Bars
Color Bars (PQ Full)
Color Bars (PQ Limited)
Color Bars (HLG)
PLUGE
PLUGE (PQ/HLG)
Off
Sets the test pattern built into the main unit.
• If the power is turned off once and then back on, the test pattern will not be
displayed.
• The test pattern will be erased in the following cases:
-
When a channel is changed using the CH button, F button assigned for
Channel UP/Channel DOWN, or [Select Channel] under [Channel Settings]
-
When changing [Input Configuration] or [Select Input Signal] under [Channel
Settings]
-
When [Reset All Settings] is executed
Signal Monitoring
Monitors the input signal status.
• [Signal Monitoring] cannot be used in the following cases:
-
When [Single Input Dual View] is displayed
-
When an enlarged image is displayed
-
During display of the test pattern
-
During execution of [Playback File] under [Screen Capture]
• When an error is displayed, [In Monitor Display] will not be shown.
• The position the error is displayed can be adjusted with [In Monitor Display]
[Position].
Control
On,
Off
Sets whether [Signal Monitoring] is used or not.
Error Hold
On (No time out)
On (5 sec.)
Off
Sets the length of time for displaying errors, when they are detected.
[On (No time out)]: Errors continue to be displayed. To hide the displayed
error, press the RESET button when closing the OSD menu.
[On (5 sec.)]: The displayed error will disappear 5 seconds after the initial
detection.
[Off]: Only displays errors during the period when they are detected. The
displayed error message will disappear once the error ends.
No Signal/Unsupported
Signal
On
, Off
Displays an error when there is [No Signal] or [Unsupported Signal].