Canon ME-200S SH User Manual - Page 16

Using the DC IN 2 Terminal, DC IN 2 terminal configuration

Get Canon ME-200S SH PDF manuals and user guides View all Canon ME-200S SH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Preparing the Power Supply Using the DC IN 2 Terminal Follow this procedure to prepare a power cable using the supplied power connector and power the camera using the DC IN 2 terminal. DC IN 2 terminal configuration Polarity Signal 16 + 11 to 17 V DC - Ground Terminal type: 2-pin socket ቤ (male connector) Torque: 0.25 N·m (max.) Polarity: + 1 Strip the insulation from the tips of the power cable wires. • For reference only: The wire gauge of power cables that can be used is AWG 24 to 16. 2 Insert the tips of the wires into the supplied power connector as shown in the illustration. • Make sure to connect the wires to match the polarity indicators on the DC IN 2 terminal. 3 Tighten the screws of the supplied power connector to securely attach the wires. • Set a tightening torque of no more than 0.25 N·m. 4 Set the Q switch to OFF. 5 Insert the power connector into the DC IN 2 terminal. Polarity: - ባ Power connector (supplied) Strip ቢ Approx. 5 to 7 mm (0.20 to 0.28 in.) ቦ IMPORTANT • Make sure to use an external power supply that meets ብ the standards of the country/region where it is used. Furthermore, make sure the external power supply is a double-insulated device and is insulated for commercial power use.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Preparing the Power Supply
16
Using the DC IN 2 Terminal
±
²
³
Torque: 0.25 N·m
(max.)
Strip
Approx. 5 to 7 mm
(0.20 to 0.28 in.)
Power connector
(supplied)
Polarity: +
Follow this procedure to prepare a power cable using the supplied power connector and power the
camera using the DC IN 2 terminal.
DC IN 2 terminal configuration
Polarity
Signal
+
11 to 17 V DC
-
Ground
´
µ
1
Strip the insulation from the tips of the power
cable wires.
•
For reference only: The wire gauge of power cables
that can be used is AWG 24 to 16.
2
Insert the tips of the wires into the supplied power
connector as shown in the illustration.
•
Make sure to connect the wires to match the polarity
indicators on the DC IN 2 terminal.
3
Tighten the screws of the supplied power
connector to securely attach the wires.
•
Set a tightening torque of no more than 0.25 N·m.
4
Set the
Q
switch to OFF.
5
Insert the power connector into the DC IN 2
terminal.
IMPORTANT
•
Make sure to use an external power supply that meets
the standards of the country/region where it is used.
Furthermore, make sure the external power supply is a
double-insulated device and is insulated for commercial
power use.
Polarity: -
Terminal type: 2-pin socket
(male connector)