Canon PIXMA MP800 Service Manual - Page 19

See 3, Special Notes on Repair Servicing, 3 Flexible cable and harness wiring, connection

Get Canon PIXMA MP800 PDF manuals and user guides View all Canon PIXMA MP800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Timing slit strip film QC1-6526 Timing slit disk film QC1-6229 - Upon contact with the film, wipe the film with ethanol. - Confirm no grease is on the film. (Wipe off any grease thoroughly with ethanol.) - Do not bend the film [See 3.3. Adjustment / Settings, (2) Grease application.] After replacement: - Service test print 1. Perform the print head alignment in the user mode. Print head QY6-0061 After replacement: - Service test print 1. Perform the print head alignment in the user mode. *1: General notes: - Make sure that the flexible cables and wires in the harness are in the proper position and connected correctly. [See 3-2. Special Notes on Repair Servicing, (3) Flexible cable and harness wiring, connection, for details.] - Do not drop the ferrite core, which may cause damage. - Protect electrical parts from damage due to static electricity. - Before removing a unit, after removing the power cord, allow the machine to sit for approx. 1 minute (for capacitor discharging to protect the logic board ass'y from damages). - Do not touch the timing slit strip film and timing slit disk film. No grease or abrasion is allowed. - Protect the units from soiled with ink. - Protect the housing from scratches. - Exercise caution with the red screws, as follows: i. The red screws of the paper feed motor may be loosened only at replacement of the paper feed motor unit (DO NOT loosen them in other cases). ii. DO NOT loosen the red screws on both sides of the main chassis, securing the carriage shaft positioning (they are not adjustable in servicing) To the table of contents To the top 1-14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
*1:
General notes:
- Make sure that the flexible cables and wires in the harness are in the proper position and connected correctly.
[See 3
-
2. Special Notes on Repair Servicing, (3) Flexible cable and harness wiring, connection, for details.]
- Do not drop the ferrite core, which may cause damage.
- Protect electrical parts from damage due to static electricity.
- Before removing a unit, after removing the power cord, allow the machine to sit for approx. 1 minute (for capacitor
discharging to protect the logic board ass'y from damages).
- Do not touch the timing slit strip film and timing slit disk film. No grease or abrasion is allowed.
- Protect the units from soiled with ink.
- Protect the housing from scratches.
- Exercise caution with the red screws, as follows:
i.
The red screws of the paper feed motor may be loosened only at replacement of the paper feed motor unit (DO
NOT loosen them in other cases).
ii.
DO NOT loosen the red screws on both sides of the main chassis, securing the carriage shaft positioning (they are
not adjustable in servicing)
[See 3.3. Adjustment / Settings,
(2) Grease application.]
Timing slit strip film
QC1-6526
- Upon contact with the film,
wipe the film with ethanol.
- Confirm no grease is on the
film. (Wipe off any grease
thoroughly with ethanol.)
- Do not bend the film
After replacement:
1.
Perform the print head
alignment in the user mode.
- Service test print
Timing slit disk film
QC1-6229
Print head
QY6-0061
After replacement:
1.
Perform the print head
alignment in the user mode.
- Service test print
To the table of contents
To the top
<Part 1:
3. REPAIR, 3-1>
1-14