Canon imageFORMULA CR-180 CR-180 Instruction Manual - Page 20

Setting Up the Scanner

Get Canon imageFORMULA CR-180 PDF manuals and user guides View all Canon imageFORMULA CR-180 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Chapter 2 Preparation Before Use Setting Up the Scanner Perform the following steps to set up the CR-180. Refer to the section for each step for details about that step. 1. Check your operating environment (See "Checking Your Operating Environment," on p.17.) d 2. Install the software (See "Installing the Software," on p.19.) Install the Scanning Utility provided with the CR-180. d 3. Connect the scanner to a computer (See "Connecting the Scanner to a Computer," on p.23.) You need to turn off the computer before connecting the CR-180 to it with a SCSI cable. d 4. Turn ON the power (See "Turning ON the Power," on p.26.) Turn on the CR-180 before turning on the computer if they are connected with a SCSI cable. d 5. Automatically installing the device driver (See p.27.) The device driver is installed automatically when Windows recognizes the CR180. Important ● To have the device drivers installed automatically when the computer recognizes the CR-180, the software needs to be installed before the CR-180 is connected to the computer. ● If you connect the computer and turn on the CR-180 before installing the software, the following wizard appears. If this happens, click [Cancel] to close the wizard's window, turn off the CR-180 and then install the software. Wizard Screen (Windows 2000) 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
16
Chapter 2
Preparation Before Use
Setting Up the Scanner
Perform the following steps to set up the CR-180. Refer to the section for each
step for details about that step.
1.
Check your operating environment (See “Checking Your Operating
Environment,” on p.17.)
d
2.
Install the software (See “Installing the Software,” on p.19.)
Install the Scanning Utility provided with the CR-180.
d
3.
Connect the scanner to a computer (See “Connecting the Scanner to a
Computer,” on p.23.)
You need to turn off the computer before connecting the CR-180 to it with a
SCSI cable.
d
4.
Turn ON the power (See “Turning ON the Power,” on p.26.)
Turn on the CR-180 before turning on the computer if they are connected with
a SCSI cable.
d
5.
Automatically installing the device driver (See p.27.)
The device driver is installed automatically when Windows recognizes the CR-
180.
●
To have the device drivers installed automatically when the computer recognizes the
CR-180, the software needs to be installed before the CR-180 is connected to the
computer.
●
If you connect the computer and turn on the CR-180 before installing the software,
the following wizard appears. If this happens, click [Cancel] to close the wizard’s
window, turn off the CR-180 and then install the software.
Important
Wizard Screen (Windows 2000)