Canon imageFORMULA CR-180 CR-180 Instruction Manual - Page 51

CR-180 must their terminators OFF. See Setting the SCSI ID,

Get Canon imageFORMULA CR-180 PDF manuals and user guides View all Canon imageFORMULA CR-180 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

5.1 When the Scanner Is Not Recognized Cause Remedy The same SCSI ID is used for other SCSI devices (when using SCSI connections). Check the SCSI ID of all connected SCSI devices, and make sure that the same SCSI ID is not set for two or more devices. Reset the SCSI IDs if the same SCSI ID is set. (See "Setting the SCSI ID," on p.24.) Cause Remedy Another SCSI device is valid as a terminator (when using SCSI connections). Cancel the SCSI device terminator that is connected between the CR-180 and the computer. The CR-180 must be at the end of the daisy chain, and all other SCSI devices in between the computer and CR-180 must their terminators OFF. (See "Setting the SCSI ID," on p.24.) Cause Remedy The scanner was turned ON after turning ON the computer (when using SCSI connections). Turn the computer and scanner OFF, turn ON the scanner, and then turn ON the computer. (See "Turning ON and OFF the Power," on p.26.) 5 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
47
5
5.1
When the Scanner Is Not Recognized
Cause
The same SCSI ID is used for other SCSI devices (when using
SCSI connections).
Remedy
Check the SCSI ID of all connected SCSI devices, and make sure that
the same SCSI ID is not set for two or more devices. Reset the SCSI
IDs if the same SCSI ID is set. (See “Setting the SCSI ID,” on p.24.)
Cause
Another SCSI device is valid as a terminator (when using SCSI
connections).
Remedy
Cancel the SCSI device terminator that is connected between the
CR-180 and the computer. The CR-180 must be at the end of the
daisy chain, and all other SCSI devices in between the computer and
CR-180 must their terminators OFF. (See “Setting the SCSI ID,” on
p.24.)
Cause
The scanner was turned ON after turning ON the computer (when
using SCSI connections).
Remedy
Turn the computer and scanner OFF, turn ON the scanner, and then
turn ON the computer. (See “Turning ON and OFF the Power,” on
p.26.)