Cisco SPA2102-AU Provisioning Guide - Page 67

Firmware Upgrade Parameters

Get Cisco SPA2102-AU PDF manuals and user guides View all Cisco SPA2102-AU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Chapter 4 Provisioning Field Reference Firmware Upgrade Parameters Firmware Upgrade Parameters The following table defines the function and usage of each parameter in the Firmware Upgrade section of the Provisioning tab. Table 4-2 Firmware Upgrade Parameters Parameter Name Upgrade_Enable Upgrade_Error_Retry_Delay Downgrade_Rev_Limit Upgrade_Rule Log_Upgrade_Request_Msg Log_Upgrade_Success_Msg Log_Upgrade_Failure_Msg License Keys Description and Default Value Enables firmware upgrade operations independently of resync actions. The default is Yes. The upgrade retry interval (in seconds) applied in case of upgrade failure. The device has a firmware upgrade error timer that activates after a failed firmware upgrade attempt. The timer is initialized with the value in this parameter. The next firmware upgrade attempt occurs when this timer counts down to zero. The default is 3600 seconds. Enforces a lower limit on the acceptable version number during a firmware upgrade or downgrade. The device does not complete a firmware upgrade operation unless the firmware version is greater than or equal to this parameter. The default is (empty). This parameter is a firmware upgrade script with the same syntax as Profile_Rule. Defines upgrade conditions and associated firmware URLs. The default is (empty). Syslog message issued at the start of a firmware upgrade attempt. The default is $PN $MAC -- Requesting upgrade $SCHEME://$SERVIP:$PORT$PATH. Syslog message issued after a firmware upgrade attempt completes successfully. The default is $PN $MAC -- Successful upgrade $SCHEME://$SERVIP:$PORT$PATH -- $ERR. Syslog message issued after a failed firmware upgrade attempt. The default is $PN $MAC -- Upgrade failed: $ERR. This field is empty. Version 3.0 Linksys SPA Provisioning Guide 4-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
4-5
Linksys SPA Provisioning Guide
Version 3.0
Chapter 4
Provisioning Field Reference
Firmware Upgrade Parameters
Firmware Upgrade Parameters
The following table defines the function and usage of each parameter in the Firmware Upgrade section
of the Provisioning tab.
Table 4-2
Firmware Upgrade Parameters
Parameter Name
Description and Default Value
Upgrade_Enable
Enables firmware upgrade operations
independently of resync actions.
The default is Yes.
Upgrade_Error_Retry_Delay
The upgrade retry interval (in seconds) applied in
case of upgrade failure. The device has a
firmware upgrade error timer that activates after
a failed firmware upgrade attempt. The timer is
initialized with the value in this parameter. The
next firmware upgrade attempt occurs when this
timer counts down to zero.
The default is 3600 seconds.
Downgrade_Rev_Limit
Enforces a lower limit on the acceptable version
number during a firmware upgrade or
downgrade. The device does not complete a
firmware upgrade operation unless the firmware
version is greater than or equal to this parameter.
The default is (empty).
Upgrade_Rule
This parameter is a firmware upgrade script with
the same syntax as Profile_Rule. Defines
upgrade conditions and associated firmware
URLs.
The default is (empty).
Log_Upgrade_Request_Msg
Syslog message issued at the start of a firmware
upgrade attempt.
The default is $PN $MAC -- Requesting upgrade
$SCHEME://$SERVIP:$PORT$PATH.
Log_Upgrade_Success_Msg
Syslog message issued after a firmware upgrade
attempt completes successfully.
The default is $PN $MAC -- Successful upgrade
$SCHEME://$SERVIP:$PORT$PATH -- $ERR.
Log_Upgrade_Failure_Msg
Syslog message issued after a failed firmware
upgrade attempt.
The default is $PN $MAC -- Upgrade failed:
$ERR.
License Keys
This field is empty.