Cisco WAE-674-K9 Hardware Installation Guide - Page 132

Minimum configuration: 1230 Btu, Heat Output

Get Cisco WAE-674-K9 - Wide Area Application Engine 674 PDF manuals and user guides
UPC - 882658200076
View all Cisco WAE-674-K9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 132 highlights

Appliance Specifications Appendix A Wide Area Application Engine Hardware Specifications Table A-1 WAE 7371, 7341, and 674 Features and Specifications (continued) Specification Description Environment • Air temperature: - Device on: 50 to 95° F (10 to 35° C); altitude: 0 to 914.4 m (3000 ft) - Device off: 50 to 109.4° F (10 to 43° C); maximum altitude: 2133 m (7000 ft) • Humidity - Device on: 8 to 80% - Device off: 8 to 80% 1Acoustical noise emissions • Declared sound power, idle: 6.8 bel2 3Heat Output • Declared sound power, operating: 6.8 bel • Minimum configuration: 1230 Btu4 (360 watts) • Maximum configuration: 3390 Btu (835 watts) 1. These levels were measured in controlled acoustical environments according to the procedures specified by the American National Standards Institute (ANSI) S12.10 and ISO 7779 and are reported in accordance with ISO 9296. Actual sound-pressure levels in a given location might exceed the average values stated because of room reflections and other nearby noise sources. The declared sound-power levels indicate an upper limit, below which a large number of computers will operate. 2. In acoustics, the logarithm of the ratio of a quantity to a reference quantity of the same kind is called a level. The base of the logarithm (always ten, unless otherwise specified), the reference quantity, and the kind of level shall be specified. bel is a unit of level when the base of the logarithm is ten, and the quantities concerned are proportional to power. 3. Power consumption and heat output vary depending on the number and type of optional features installed and the power-management optional features in use. 4. BTU = British Thermal Unit. Cisco Wide Area Application Engine 7341, 7371, and 674 Hardware Installation Guide A-4 OL-15012-02

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
Appendix A
Wide Area Application Engine Hardware Specifications
Appliance Specifications
A-4
Cisco Wide Area Application Engine 7341, 7371, and 674 Hardware Installation Guide
OL-15012-02
Environment
•
Air temperature:
–
Device on: 50 to 95
°
F (10 to 35
°
C); altitude: 0 to 914.4 m
(3000 ft)
–
Device off: 50 to 109.4
°
F (10 to 43
°
C); maximum altitude:
2133 m (7000 ft)
•
Humidity
–
Device on: 8 to 80%
–
Device off: 8 to 80%
1
Acoustical noise emissions
•
Declared sound power, idle: 6.8 bel
2
•
Declared sound power, operating: 6.8 bel
3
Heat Output
•
Minimum configuration: 1230 Btu
4
(360 watts)
•
Maximum configuration: 3390 Btu (835 watts)
1.
These levels were measured in controlled acoustical environments according to the procedures specified by the American
National Standards Institute (ANSI) S12.10 and ISO 7779 and are reported in accordance with ISO 9296. Actual
sound-pressure levels in a given location might exceed the average values stated because of room reflections and other nearby
noise sources. The declared sound-power levels indicate an upper limit, below which a large number of computers will
operate.
2.
In acoustics, the logarithm of the ratio of a quantity to a reference quantity of the same kind is called a level. The base of the
logarithm (always ten, unless otherwise specified), the reference quantity, and the kind of level shall be specified. bel is a unit
of level when the base of the logarithm is ten, and the quantities concerned are proportional to power.
3.
Power consumption and heat output vary depending on the number and type of optional features installed and the
power-management optional features in use.
4.
BTU = British Thermal Unit.
Table A-1
WAE 7371, 7341, and 674 Features and Specifications (continued)
Specification
Description