Cisco WAE-674-K9 Hardware Installation Guide - Page 33

Tools and Parts Required

Get Cisco WAE-674-K9 - Wide Area Application Engine 674 PDF manuals and user guides
UPC - 882658200076
View all Cisco WAE-674-K9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Chapter 3 Installing the Wide Area Application Engine Tools and Parts Required • Minimum depth of 28.27 inches (718 mm) and maximum depth of 30 inches (762 mm) between the front and rear mounting flanges to support the use of the cable-management arm. Racks are marked in vertical increments of 1.75 inches (4.44 cm). Each increment is referred to as a rack unit (RU). A 1-RU device is 1.75 inches (4.44 cm) tall. Tools and Parts Required A sliding rail rack-mount kit is included in your shipping container accessory box. The rack-mount kit is suitable for mounting the WAE-7371, WAE-7341, and WAE-674 appliances in 19-inch (48.26-cm), 4-post equipment racks. (See the "Rack Requirements" section on page 3-2.) You need the following tools for the installation: • Flat-blade screwdriver • Phillips screwdriver Figure 3-1 shows the items that you need to install the WAE in your rack or cabinet. If any items are missing or damaged, contact your customer service representative. Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: • This unit should be mounted at the bottom of the rack if it is the only unit in the rack. • When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. • If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. Statement 1006 OL-15012-02 Cisco Wide Area Application Engine 7341, 7371, and 674 Hardware Installation Guide 3-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
3-3
Cisco Wide Area Application Engine 7341, 7371, and 674 Hardware Installation Guide
OL-15012-02
Chapter 3
Installing the Wide Area Application Engine
Tools and Parts Required
•
Minimum depth of 28.27 inches (718 mm) and maximum depth of 30 inches
(762 mm) between the front and rear mounting flanges to support the use of
the cable-management arm.
Racks are marked in vertical increments of 1.75 inches (4.44 cm). Each increment
is referred to as a rack unit (RU). A 1-RU device is 1.75 inches (4.44 cm) tall.
Tools and Parts Required
A sliding rail rack-mount kit is included in your shipping container accessory box.
The rack-mount kit is suitable for mounting the WAE-7371, WAE-7341, and
WAE-674 appliances in 19-inch (48.26-cm), 4-post equipment racks. (See the
“Rack Requirements” section on page 3-2
.)
You need the following tools for the installation:
•
Flat-blade screwdriver
•
Phillips screwdriver
Figure 3-1
shows the items that you need to install the WAE in your rack or
cabinet. If any items are missing or damaged, contact your customer service
representative.
Warning
To prevent bodily injury when mounting or servicing this unit in a rack, you
must take special precautions to ensure that the system remains stable. The
following guidelines are provided to ensure your safety:
•
This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
•
When mounting this unit in a partially filled rack, load the rack from the bottom to the
top with the heaviest component at the bottom of the rack.
•
If the rack is provided with stabilizing devices, install the stabilizers before mounting
or servicing the unit in the rack.
Statement 1006