Cisco WAE-674-K9 Hardware Installation Guide - Page 35

Installing the Wide Area Application Engine

Get Cisco WAE-674-K9 - Wide Area Application Engine 674 PDF manuals and user guides
UPC - 882658200076
View all Cisco WAE-674-K9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Chapter 3 Installing the Wide Area Application Engine Installing the Wide Area Application Engine Installing the Wide Area Application Engine Place the WAE in the desired location. You can mount it in a rack or place it on a solid, stable surface. If you do not plan to install the appliance in an equipment rack, proceed to the "Installing the Chassis on a Tabletop" section on page 3-10. To install the WAE in a rack, follow these steps: Step 1 Push outward on the slide-rail latch (labeled 2 in Figure 3-2). Pull the latch back to open the slide rail. The latch will engage and stay open. Open the other end of the slide rail. Repeat the entire process for the other slide rail. Note If you are installing the WAE in the top of the rack or directly under another device, remove the cable-management arm bracket from the cable-management assembly and install the cable-management arm bracket on the slide rail. Go to Step 6 to install the cable-management arm bracket, and continue with Step 2. Figure 3-2 Latching the Slide Rails 2 134570 1 OL-15012-02 1 Right slide rail 2 Slide rail latch Cisco Wide Area Application Engine 7341, 7371, and 674 Hardware Installation Guide 3-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
3-5
Cisco Wide Area Application Engine 7341, 7371, and 674 Hardware Installation Guide
OL-15012-02
Chapter 3
Installing the Wide Area Application Engine
Installing the Wide Area Application Engine
Installing the Wide Area Application Engine
Place the WAE in the desired location. You can mount it in a rack or place it on a
solid, stable surface. If you do not plan to install the appliance in an equipment
rack, proceed to the
“Installing the Chassis on a Tabletop” section on page 3-10
.
To install the WAE in a rack, follow these steps:
Step 1
Push outward on the slide-rail latch (labeled 2 in
Figure 3-2
). Pull the latch back
to open the slide rail. The latch will engage and stay open. Open the other end of
the slide rail. Repeat the entire process for the other slide rail.
Note
If you are installing the WAE in the top of the rack or directly under another
device, remove the cable-management arm bracket from the cable-management
assembly and install the cable-management arm bracket on the slide rail. Go to
Step 6 to install the cable-management arm bracket, and continue with Step 2.
Figure 3-2
Latching the Slide Rails
134570
2
1
1
Right slide rail
2
Slide rail latch