Craftsman 536.270320 Owners Manual - Page 27

How To Remove, The Mower, Housing, How To Install

Get Craftsman 536.270320 - 13.5 HP 30 in. Deck PDF manuals and user guides View all Craftsman 536.270320 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

SERVICE AND ADJUSTMENT HOW TO REMOVE THE MOWER HOUSING 1. Move the lift lever to the middle position 2 Move the attachment clutch to the DISENGAGE position (Figure 31 ) 3. Disconnect the blade drive link from the pivot rod and bracket assembly See illustration "C". 4. Remove the hair pins from the adjuster plates See illustrations "A" and "B". 5 Move the mower housing to the left until the right side adjuster plate separates from the hanger. See illustration "A". 6 Move the mower housing to the rightuntit the left side adjuster plate separates from the hanger. See illustration "B". 7. Remove the long pin from the front hanger. See illustration lIg_ - Remove the mower drive belt fromthe stack pulley. Slide the mower drive belt between the stack pulley and the belt guide 9. Completely turn the steering wheel to the right. Pull the mower housing away from the left side of the unit. HOW TO INSTALL THE MOWER HOUSING 1. Completely turn the steering wheelto the right. Push the mower housing under the left side of the unit. 2 Slide the mower drive belt between the stack pulley and the belt guide Put the mower drive belt around the stack pulley Make sure the "V" side of the mower drive belt is against the stack pulley. Also, make sure the mower drive belt is not twisted. 3. Attach the mower housing to the front hanger with the long pin. Fasten with the washer and hair pin. See illustration "D" 4 Attach the adjuster plates to the hangers with the hair pins See illustrations"A" and "B" 5 Connect the blade drive link to the pivot rod and bracket assembly with the fasteners. See illustration "C'. 6. Move the attachment clutch to the ENGAGE position Make sure the mower drive belt is inside all the belt guides. 7. Make sure the mower housing is level See the instructions on "How To Level The Mower Housing". 8 Check the operation of the attachment clutch. See the instructions on "How To Adjust The Attachment Clutch". Stack Pulley t Belt Guide Blade Drive Link Attachment Clutch Hanger B / Hair Pin Mower DnveBelt \ Lift Lever Adj Hanger Long Pin /" D /__1 c B'_lade DnveLink F-99636 Downloaded from www.Manualslib.com manuals search engine Front Hanger 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
SERVICE
AND ADJUSTMENT
HOW TO REMOVE
THE MOWER
HOUSING
1.
Move the lift lever to the middle position
Move the attachment
clutch
to the DISENGAGE
position
(Figure 31 )
2
3.
4.
5
6
7.
Disconnect
the blade
drive link from
the pivot rod and brack-
et assembly
See illustration "C".
Remove
the
hair
pins from the
adjuster
plates
See illustra-
tions "A" and "B".
Move the
mower
housing to the left until the right side
adjuster
plate separates from the hanger. See illustration "A".
Move the mower housing to the
right
untit the left side
adjuster
plate separates from the hanger. See illustration "B".
Remove
the long pin from the front
hanger.
See illustration
lIg_
-
9.
Remove
the mower drive
belt
from
the stack
pulley.
Slide the
mower drive
belt between the stack pulley
and the belt
guide
Completely
turn the steering
wheel
to
the right.
Pull the
mower
housing
away
from
the left side
of the unit.
HOW TO INSTALL
THE MOWER
HOUSING
1.
Completely turn the steering wheelto the right. Push the mower
housing under the left side of the unit.
2
Slide the
mower
drive belt between the
stack pulley
and the
belt
guide
Put the mower drive belt around the
stack
pulley
Make sure the "V" side of the mower
drive
belt is
against
the
stack
pulley.
Also, make sure the
mower
drive
belt is not
twisted.
3.
Attach the mower housing
to the front
hanger with the long
pin.
Fasten with the washer and hair pin. See illustration "D"
4
Attach the
adjuster
plates to the
hangers
with the hair pins
See
illustrations
"A"
and "B"
5
Connect the
blade
drive
link to the
pivot
rod and
bracket
assembly
with the fasteners. See illustration "C'.
6.
Move the
attachment clutch
to the ENGAGE position
Make
sure the mower
drive belt is inside all the belt
guides.
7.
Make sure the mower housing is level See the instructions on
"How To Level The Mower Housing".
8
Check the operation of the attachment
clutch.
See the instruc-
tions on "How To Adjust The Attachment Clutch".
Stack
Pulley
t
Belt Guide
Hanger
B
/
Hair Pin
MowerDnveBelt
\
Lift Lever
Blade
Drive
Link
Attachment
Clutch
Long Pin
/"
D
Adj
Hanger
Front Hanger
/__1
c B'_lade
DnveLink
F-99636
27
Downloaded from
www.Manualslib.com
manuals search engine