Craftsman 536.270320 Owners Manual - Page 33
Trouble, Chart - parts diagram
View all Craftsman 536.270320 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 33 highlights
TROUBLE SHOOTING CHART PROBLEM: The engine will not start. 1 Follow the steps, =HowTo Start The Engine" in this book 2 Electric-Start Models Clean the battery terminals 33ghten the cables 3 Check for a loose wire Tighten the limit switches. (See the wiring diagram.) 4 Drain the fuel tank Clean the fuel fine Replace the fuel filter. 5. Remove the spark plug(s). Move the throttle to the SLOW posi- tion. Turn the ignition key to the ON position.Try to start the engine several times install the spark plug 6. Replace the spark plug 7. Adjust the carburetor PROBLEM: The engine will not turn over. t. Follow the steps, "Hew To Start The Engine" in this book. 2 Electric-Start Models: Check the level of the acid in the battery tf needed, add water. Charge the battery 3. Replace the fuse. 4 Check the wiring harness for damage or a loose connection Repair the damaged wire 5. Electric-Start Models replace the solenoid. Recoil-Start Mod- els: replace the module. PROBLEM: A hot engine causes a decrease in power, 1. Clean the air screen 2 Check the oil 3 Adjust the carburetor 4 Replace the fuel filter PROBLEM: Excessive vibration, 1. Replace the blade 2 Check for loose engine botts. 3 Decrease the air pressure in the tires 4. Adjust the carburetor 5. Check for a damaged belt or damaged pulley Replace the damaged parts. PROBLEM: The grass does not discharge correctly. t. Stop the engine Clean the mower housing 2. Raise the height of cut. 3. Replace or sharpen the blade(s). 4. Move the shift lever to a slower speed. 5. Move the throttle control to the FAST position. 6. Replace the spring for the blade idler. PROBLEM: The engine is difficult 1 Adjust the carburetor 2 Replace the spark plug 3 Replace the fuel filter to start. PROBLEM: The engine does not run smooth or has a loss of power. 1 Check the oil. 2. Clean the air filter. 3 Clean the air screen. 4 Replace the spark plug 5. The engine is working too hard. Use a lower gear 6 Adjust the carburetor 7. Replace the fuel filter PROBLEM: The engine does speed. 1 Replace the spark piug 2 Adjust the throttle control 3. Clean the air filter. 4. Replace the fuel filter not run smooth at fast PROBLEM: The mower housing does not cut level. t. Check the air pressure in the tires 2. Adjust the level of the mower housing 3. Check the front axle If the frontaxle does not freelypivot, loos- en the axle bolt(s). PROBLEM: The mower blades will not rotate. 1. Check the mower drive belt Make sure the belt is installedcor- rectTy. 2, Replace the mower drive belt PROBLEM: The unit will not move when the clutch is engaged. 1. Check the motion drive belt Make sure the belt is installed correctly. 2. Adjust the clutch 3. Replace the motion drive belt PROBLEM: The unit moves slower or stops when the clutch is engaged. 1. Adjust the clutch 2. Replace the motion drive belt. PROBLEM: The engine stops when the blades are engaged. I. Toactivate the seat sensor, always sit inthe middle of the seat 2 Check the wiring harness for damage or a loose connection. Repair the damaged wire. PROBLEM: On slopes, the engine stops. 1. Mow up and down slopes Never mow across a slope 2 To activate the seat sensor, always sit in the middle of the seat PROBLEM: When the clutch/brake pedal is released, belt noise can be heard. 1. Temporarybelt noisedoes notchangethe operation ofthe unit. tt belt noise is continuous, check the routing of the belt Make sure the belt is inside all belt guides. 2 If the noise is continuous, adjust the clutch. PROBLEM: The rear wheels spin over uneven terrain. 1. Check the front axle. If the front axle does not freely pivot, loos- en the axle bolt(s). PROBLEM: The engine will not idle. 1 Replace the spark plug. 2 Clean the air filter 3 Adjust the carburetor 4 Adjust the throttle control 5 Drain the fuel tank Clean the fuel line F-99636 Replace the fuel filter PROBLEM: The transaxle is difficult to shift between gears with the engine running and the clutch depressed. 1. Check the clutch adjustment to make sure the belt stops when the clutch pedal is depressed with the transaxle in (N) neutral 2 33 Check the belt guides around the transaxle drive pulley Make sure the belt guides do not touch the pulley Downloaded from www.Manualslib.com manuals search engine