D-Link DHP-W306AV Product Manual - Page 61

Start > Settings > Control Panel - repeater

Get D-Link DHP-W306AV PDF manuals and user guides
UPC - 790069339226
View all D-Link DHP-W306AV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Section 3 - Configuration • Configure your Internet settings: • Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. • Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. • Go to the Advanced tab and click the Reset... button to restore these settings to their defaults. Click OK three times. • Close your web browser (if open) and open it. • Access the web management. Open your web browser and enter the IP address of your D-Link access point in the address bar. This should open the login page for your the web management. • If you still cannot access the configuration, unplug the power to the access point for 10 seconds and plug back in. Wait about 30 seconds and try accessing the configuration. If you have multiple computers, try connecting using a different computer. 2. What can I do if I forgot my password? If you forgot your password, you must reset your access point. Unfortunately this process will change all your settings back to the factory defaults. To reset the access point, locate the reset button (hole) on the rear panel of the unit. With the access point powered on, use a paperclip to hold the button down for 5 seconds. Release the button and the access point will go through its reboot process. Wait about 30 seconds to access the access point. The default IP address is 192.168.0.50. When logging in, the username is Admin and leave the password box empty 3. Why can't my PowerLine AV device detect my other PowerLine AV devices. This may due to the accidental change of the device password. Use the web-based configuration utility and select Setup > PLC SETTINGS. Fill in the password in the blank. Then repeat the same procedure to the other PowerLine AV device via web-based configuration utility. 4. I cannot start my PowerLine AV device. Please check your power supply is working. PowerLine AV device operates from the power supplied by the home electrical wiring and can not operate without a working power supply. D-Link DHP-W306AV User Manual 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
61
D-Link DHP-W306AV User Manual
Section 3 - Configuration
• Configure your Internet settings:
• Go to
Start > Settings > Control Panel
. Double-click the Internet Options Icon. From the Security tab, click the button to restore the
settings to their defaults.
•
Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the
LAN Settings
button. Make sure nothing is
checked. Click
OK
.
• Go to the Advanced tab and click the Reset... button to restore these settings to their defaults. Click
OK
three times.
• Close your web browser (if open) and open it.
• Access the web management. Open your web browser and enter the IP address of your D-Link access point in the address bar. This should
open the login page for your the web management.
• If you still cannot access the configuration, unplug the power to the access point for 10 seconds and plug back in. Wait about 30 seconds
and try accessing the configuration. If you have multiple computers, try connecting using a different computer.
2. What can I do if I forgot my password?
If you forgot your password, you must reset your access point. Unfortunately this process will change all your settings back to the factory defaults.
To reset the access point, locate the reset button (hole) on the rear panel of the unit. With the access point powered on, use a paperclip to hold the
button down for 5 seconds. Release the button and the access point will go through its reboot process. Wait about 30 seconds to access the access
point. The default IP address is 192.168.0.50. When logging in, the username is Admin and leave the password box empty
3. Why can’t my PowerLine AV device detect my other PowerLine AV devices.
This may due to the accidental change of the device password. Use the web-based configuration utility and select
Setup > PLC SETTINGS
. Fill in
the password in the blank. Then repeat the same procedure to the other PowerLine AV device via web-based configuration utility.
4. I cannot start my PowerLine AV device.
Please check your power supply is working. PowerLine AV device operates from the power supplied by the home electrical wiring and can not
operate without a working power supply.