D-Link DS-510S User Guide - Page 51

Static IP Address, Connection Type, Virtual Circuit, IP Address, Subnet Mask, ISP Gateway Address,

Get D-Link DS-510S PDF manuals and user guides View all D-Link DS-510S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

DSL-510 ADSL Router User's Guide Home＞WAN＞Static IP Address Choose Static IP Address if all WAN IP information is provided to you by your ISP. You will need to enter in the VPI, VCI, IP Address, Subnet Mask, ISP Gateway Address, DNS Address and select connection type provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four IP octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format. VPI: If instructed to change this, type in the VPI value for the initial connection. VCI: If instructed to change this, type in the VCI value for the initial connection. Connection Type: Change connection method and packet encapsulation technique as instructed by your ISP. The available connection types are 1483 Bridge/Router LLC, 1483 Bridge/Router VC-Mux, RFC-1577-IPoA, form the pull-down menu. Default Connection Type = 1483 Bridge/Router LLC. Virtual Circuit: Selection Enable or Disable. IP Address: Provided by ISP. Check with your ISP to get this information. Type in the Global IP address for this interface. Subnet Mask: If you are assigned Static IP addresses and Subnet mask, Type in Subnet mask for this interface. ISP Gateway Address: Specify the IP address that identifies the ISP server through which your Internet connection will be routed. Primary/Secondary DNS Address: This option is useful only when the Router is configured to act as a DHCP Server for your LAN. Enter the Primary and Secondary DNS Server address provided by your ISP. ATM Service Category: UBR and CBR are supported form the ATM. Bandwidth: Bandwidth setting takes effect only when the CBR is selected. The maximum available bandwidth is from the upstream data rate of ADSL status page. 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
DSL-510 ADSL Router User’s Guide
42
Home
＞
WAN
＞
Static IP Address
Choose Static IP Address if all WAN IP information is provided to you by your ISP. You will need to enter in the VPI, VCI,
IP Address, Subnet Mask, ISP Gateway Address, DNS Address and select connection type provided to you by your ISP.
Each IP address entered in the fields must be in the appropriate IP form, which are four IP octets separated by a dot
(x.x.x.x). The Router will not accept the IP address if it is not in this format.
VPI:
If instructed to change this, type in the VPI value for the initial connection.
VCI:
If instructed to change this, type in the VCI value for the initial connection.
Connection Type:
Change connection method and packet encapsulation technique as instructed by your ISP. The
available connection types are 1483 Bridge/Router LLC, 1483 Bridge/Router VC-Mux, RFC-1577-IPoA, form the
pull-down menu. Default Connection Type = 1483 Bridge/Router LLC.
Virtual Circuit:
Selection Enable or Disable.
IP Address:
Provided
by ISP. Check with your ISP to get this information. Type in the Global IP address for this interface.
Subnet Mask:
If you are assigned Static IP addresses and Subnet mask, Type in Subnet mask for this interface.
ISP Gateway Address:
Specify the IP address that identifies the ISP server through which your Internet connection will
be routed.
Primary/Secondary DNS Address:
This option is useful only when the Router is configured to act as a DHCP Server for
your LAN. Enter the Primary and Secondary DNS Server address provided by your ISP.
ATM
Service Category:
UBR and CBR are supported form the ATM.
Bandwidth:
Bandwidth setting takes effect only when the CBR is selected. The maximum available bandwidth is from the
upstream data rate of ADSL status page.