Dell Alienware m16 R1 Service Manual - Page 35

Speakers, Removing the speakers

Get Dell Alienware m16 R1 PDF manuals and user guides View all Dell Alienware m16 R1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Steps 1. Align the screw holes on the I/O board with the screw holes on the palm-rest and keyboard assembly. 2. Replace the four screws (M2x2.5) that secure the I/O board to the palm-rest and keyboard assembly. 3. Connect the I/O board cable to the palm-rest and keyboard assembly and adhere the tape to secure the I/O board cable. 4. Connect the power-button cable and close the latch to secure the cable. Next steps 1. Follow the procedure from step 1 to step 8 in Installing the system board. NOTE: The system board can be removed and installed along with the fan and heat sink. This simplifies the removal and installation procedure and avoids breaking the thermal bond between the system board and heat sink. 2. Install the 2230 solid-state drive in slot three and four. 3. Install the 2280 solid-state drive or 2230 solid-state drive in slot one and two, whichever applicable. 4. Install the rear-I/O cover. 5. Install the small fan. 6. Install the top heat-sink 7. Install the wireless card. 8. Install the battery. 9. Install the base cover. 10. Follow the procedure in After working inside your computer. Speakers Removing the speakers Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the battery. 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
Steps
1.
Align the screw holes on the I/O board with the screw holes on the palm-rest and keyboard assembly.
2.
Replace the four screws (M2x2.5) that secure the I/O board to the palm-rest and keyboard assembly.
3.
Connect the I/O board cable to the palm-rest and keyboard assembly and adhere the tape to secure the I/O board cable.
4.
Connect the power-button cable and close the latch to secure the cable.
Next steps
1.
Follow the procedure from step 1 to step 8 in
Installing the system board
.
NOTE:
The system board can be removed and installed along with the fan and heat sink. This simplifies the removal and
installation procedure and avoids breaking the thermal bond between the system board and heat sink.
2.
Install the
2230 solid-state drive
in slot three and four.
3.
Install the
2280 solid-state drive
or
2230 solid-state drive
in slot one and two, whichever applicable.
4.
Install the
rear-I/O cover
.
5.
Install the
small fan
.
6.
Install the
top heat-sink
7.
Install the
wireless card
.
8.
Install the
battery
.
9.
Install the
base cover
.
10.
Follow the procedure in
After working inside your computer
.
Speakers
Removing the speakers
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
3.
Remove the
battery
.
35