Dell Alienware m16 R1 Service Manual - Page 39

Touchpad, Removing the touchpad

Get Dell Alienware m16 R1 PDF manuals and user guides View all Dell Alienware m16 R1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Steps 1. Slide the power-adapter port at an angle into the slot on the palm-rest and keyboard assembly and adhere the power-adapter port cable to the Mylar. 2. Connect the power-adapter port cable to the system board. 3. Place the power-adapter port bracket on the power-adapter port. 4. Align the screw holes on the power-adapter port bracket to the screw holes on the palm-rest and keyboard assembly. 5. Replace the two screws (M2x4) that secure the power-adapter port bracket to the palm-rest and keyboard assembly. 6. Adhere the display cable to the system board. 7. Connect the display cable to the system board and close the latch to secure the cable. 8. Adhere the tape that secures the display-cable connector latch to the system board. Next steps 1. Install the top heat-sink. 2. Install the rear-I/O cover. 3. Install the base cover. 4. Follow the procedure in After working inside your computer. Touchpad Removing the touchpad Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the battery. 4. Remove the speakers. About this task The following image(s) indicate the location of the touchpad and provides a visual representation of the removal procedure. 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
Steps
1.
Slide the power-adapter port at an angle into the slot on the palm-rest and keyboard assembly and adhere the power-adapter
port cable to the Mylar.
2.
Connect the power-adapter port cable to the system board.
3.
Place the power-adapter port bracket on the power-adapter port.
4.
Align the screw holes on the power-adapter port bracket to the screw holes on the palm-rest and keyboard assembly.
5.
Replace the two screws (M2x4) that secure the power-adapter port bracket to the palm-rest and keyboard assembly.
6.
Adhere the display cable to the system board.
7.
Connect the display cable to the system board and close the latch to secure the cable.
8.
Adhere the tape that secures the display-cable connector latch to the system board.
Next steps
1.
Install the
top heat-sink
.
2.
Install the
rear-I/O cover
.
3.
Install the
base cover
.
4.
Follow the procedure in
After working inside your computer
.
Touchpad
Removing the touchpad
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
3.
Remove the
battery
.
4.
Remove the
speakers
.
About this task
The following image(s) indicate the location of the touchpad and provides a visual representation of the removal procedure.
39