Dell Alienware m16 R1 Service Manual - Page 58

Fan and heat-sink assembly, Removing the fan and heat-sink assembly

Get Dell Alienware m16 R1 PDF manuals and user guides View all Dell Alienware m16 R1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

9. Connect the camera cable to the system board. 10. Adhere the tape securing the camera cable to the system board. 11. Connect the rear I/O board cable to the system board. 12. Connect the touchpad cable to the system board and close the latch to secure the cable. 13. Connect the speaker cable to the system board. Next steps 1. Install the battery. 2. Install the rear-I/O cover. 3. Install the small fan. 4. Install the top heat-sink. 5. Install the wireless card. 6. Install the 2230 solid-state drive in slot three and four. 7. Install the 2280 solid-state drive or 2230 solid-state drive in slot one and two, whichever applicable. 8. Install the memory. 9. Install the base cover. 10. Follow the procedure in After working inside your computer. Fan and heat-sink assembly Removing the fan and heat-sink assembly Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the 2230 solid-state drive in slot three and four. 4. Remove the 2280 solid state drive or 2230 solid-state drive in slot one and two, whichever applicable. 5. Remove the wireless card. 6. Remove the top heat-sink. 7. Remove the small fan. 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
9.
Connect the camera cable to the system board.
10.
Adhere the tape securing the camera cable to the system board.
11.
Connect the rear I/O board cable to the system board.
12.
Connect the touchpad cable to the system board and close the latch to secure the cable.
13.
Connect the speaker cable to the system board.
Next steps
1.
Install the
battery
.
2.
Install the
rear-I/O cover
.
3.
Install the
small fan
.
4.
Install the
top heat-sink
.
5.
Install the
wireless card
.
6.
Install the
2230 solid-state drive
in slot three and four.
7.
Install the
2280 solid-state drive
or
2230 solid-state drive
in slot one and two, whichever applicable.
8.
Install the
memory
.
9.
Install the
base cover
.
10.
Follow the procedure in
After working inside your computer
.
Fan and heat-sink assembly
Removing the fan and heat-sink assembly
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
3.
Remove the
2230 solid-state drive
in slot three and four.
4.
Remove the
2280 solid state drive
or
2230 solid-state drive
in slot one and two, whichever applicable.
5.
Remove the
wireless card
.
6.
Remove the
top heat-sink
.
7.
Remove the
small fan
.
58