Dell Alienware m16 R1 Service Manual - Page 65

Installing the power button, Prerequisites, About this task, Steps, Next steps

Get Dell Alienware m16 R1 PDF manuals and user guides View all Dell Alienware m16 R1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Installing the power button Prerequisites If you are replacing a component, remove the existing component before performing the installation process. About this task The following image(s) indicate the location of the power button and provides a visual representation of the installation procedure. Steps 1. Align and place the power button, along with its cable, into the slot on the palm-rest and keyboard assembly. 2. Connect the power-button cable and close the latch to secure the cable. 3. Align the screw holes on the power-button bracket to the screw holes on the palm-rest and keyboard assembly. 4. Replace the three screws (M2x2.5) that secure the power-button bracket to the palm-rest and keyboard assembly. Next steps 1. Follow the procedure from step 5 to step 13 in Installing the system board. 2. Install the battery. 3. Install the top heat-sink. 4. Install the rear-I/O cover. 5. Install the wireless card. 6. Install the 2230 solid-state drive in slot three and four. 7. Install the 2280 solid-state drive or 2230 solid-state drive in slot one and two, whichever applicable. 8. Install the base cover. 9. Follow the procedure in After working inside your computer. 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
Installing the power button
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the power button and provides a visual representation of the installation procedure.
Steps
1.
Align and place the power button, along with its cable, into the slot on the palm-rest and keyboard assembly.
2.
Connect the power-button cable and close the latch to secure the cable.
3.
Align the screw holes on the power-button bracket to the screw holes on the palm-rest and keyboard assembly.
4.
Replace the three screws (M2x2.5) that secure the power-button bracket to the palm-rest and keyboard assembly.
Next steps
1.
Follow the procedure from step 5 to step 13 in
Installing the system board
.
2.
Install the
battery
.
3.
Install the
top heat-sink
.
4.
Install the
rear-I/O cover
.
5.
Install the
wireless card
.
6.
Install the
2230 solid-state drive
in slot three and four.
7.
Install the
2280 solid-state drive
or
2230 solid-state drive
in slot one and two, whichever applicable.
8.
Install the
base cover
.
9.
Follow the procedure in
After working inside your computer
.
65