Dell Inspiron 13 N3010 Service Manual - Page 18

Display

Get Dell Inspiron 13 N3010 PDF manuals and user guides View all Dell Inspiron 13 N3010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Back to Contents Page Display Dell™ Inspiron™ N3010 Service Manual Display Assembly Display Bezel Display Panel Display Panel Bracket Display Cable Display Hinges WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on your computer). CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the computer. Display Assembly Removing the Display Assembly 1. Follow the instructions in Before You Begin. 2. Remove the battery (see Removing the Battery). 3. Remove the memory-module cover (see Removing the Memory-Module Cover). 4. Remove the memory module(s) (see Removing the Memory Module(s)). 5. Remove the two screws on the bottom of the computer that secure the display assembly to the computer base. 6. Remove the keyboard (see Removing the Keyboard). 7. Remove the palm rest assembly (see Removing the Palm Rest Assembly). 8. Open the display as far as possible. 9. Pull the pull-tab to disconnect the display cable from the connector on the system board. 10. Remove the display cable grounding screw. NOTE: Open the display at a 90-degree angle to the plane.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Back to Contents Page
Display
Dell™ Inspiron™ N3010 Service Manual
Display Assembly
Display Bezel
Display Panel
Display Panel Bracket
Display Cable
Display Hinges
Display Assembly
Removing the Display Assembly
1.
Follow the instructions in
Before You Begin
.
2.
Remove the battery (see
Removing the Battery
).
3.
Remove the memory-module cover (see
Removing the Memory
-
Module Cover
).
4.
Remove the memory module(s) (see
Removing the Memory Module(s)
).
5.
Remove the two screws on the bottom of the computer that secure the display assembly to the computer base.
6.
Remove the keyboard (see
Removing the Keyboard
).
7.
Remove the palm rest assembly (see
Removing the Palm Rest Assembly
).
8.
Open the display as far as possible.
9.
Pull the pull-tab to disconnect the display cable from the connector on the system board.
10.
Remove the display cable grounding screw.
WARNING:
Before working inside your computer, read the safety information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
CAUTION:
To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on your computer).
CAUTION:
Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™
is not covered by your warranty.
CAUTION:
To help prevent damage to the system board, remove the main battery (see
Removing the Battery
) before working inside the
computer.
NOTE:
Open the display at a 90-degree angle to the plane.