Dell Inspiron 16 5630 Service Manual - Page 40

Installing the power button, About this task, Steps, Prerequisites

Get Dell Inspiron 16 5630 PDF manuals and user guides View all Dell Inspiron 16 5630 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

2. Remove the base cover. About this task NOTE: Before removing the base cover, ensure that there is no SD card installed in the SD card slot on your computer. The following image(s) indicate the location of the power button and provides a visual representation of the removal procedure. Steps 1. Remove the two screws (M2.5x5) that secure the left display hinge to the system board. 2. Open the left display hinge at an angle of 90 degrees. 3. Remove the two screws (M2x3) that secure the power-button board to the palm-rest and keyboard assembly. 4. Open the latch and disconnect the power-button board cable from the I/O board. 5. Lift the power-button board off the palm-rest and keyboard assembly. 6. Lift the power button off the palm-rest and keyboard assembly. Installing the power button Prerequisites CAUTION: The information in this section is intended for authorized service technicians only. If you are replacing a component, remove the existing component before performing the installation process. About this task The following image(s) indicate the location of the power button and provides a visual representation of the installation procedure. 40 Removing and installing components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
2.
Remove the
base cover
.
About this task
NOTE:
Before removing the base cover, ensure that there is no SD card installed in the SD card slot on your computer.
The following image(s) indicate the location of the power button and provides a visual representation of the removal procedure.
Steps
1.
Remove the two screws (M2.5x5) that secure the left display hinge to the system board.
2.
Open the left display hinge at an angle of 90 degrees.
3.
Remove the two screws (M2x3) that secure the power-button board to the palm-rest and keyboard assembly.
4.
Open the latch and disconnect the power-button board cable from the I/O board.
5.
Lift the power-button board off the palm-rest and keyboard assembly.
6.
Lift the power button off the palm-rest and keyboard assembly.
Installing the power button
Prerequisites
CAUTION:
The information in this section is intended for authorized service technicians only.
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the power button and provides a visual representation of the installation
procedure.
40
Removing and installing components