Dell Inspiron 16 5630 Service Manual - Page 55

Touchpad, Removing the touchpad

Get Dell Inspiron 16 5630 PDF manuals and user guides View all Dell Inspiron 16 5630 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Next steps 1. Install the wireless card. 2. Install the M.2 2230 solid-state drive or M.2 2280 solid-state drive, whichever applicable. 3. Install the heat sink for computers shipped with a NVIDIA GeForce RTX 2050 graphics card or heat sink for computers shipped without a discrete graphics card, whichever applicable. 4. Install the base cover. 5. Follow the procedure in After working inside your computer. Touchpad Removing the touchpad Prerequisites CAUTION: The information in this section is intended for authorized service technicians only. 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the battery. About this task NOTE: Before removing the base cover, ensure that there is no SD card installed in the SD card slot on your computer. The following image(s) indicate the location of the touchpad and provides a visual representation of the removal procedure. Steps 1. Open the latch of the touchpad connector and disconnect the touchpad cable from the touchpad. 2. Remove the five screws (M2x2) and seven screws (M2x1.8) that secure the touchpad bracket to the palm-rest and keyboard assembly. 3. Lift the touchpad bracket off the palm-rest and keyboard assembly. 4. Lift the touchpad assembly off the palm-rest and keyboard assembly. Removing and installing components 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Next steps
1.
Install the
wireless card
.
2.
Install the
M.2 2230 solid-state drive
or
M.2 2280 solid-state drive
, whichever applicable.
3.
Install the
heat sink for computers shipped with a NVIDIA GeForce RTX 2050 graphics card
or
heat sink for computers
shipped without a discrete graphics card
, whichever applicable.
4.
Install the
base cover
.
5.
Follow the procedure in
After working inside your computer
.
Touchpad
Removing the touchpad
Prerequisites
CAUTION:
The information in this section is intended for authorized service technicians only.
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
3.
Remove the
battery
.
About this task
NOTE:
Before removing the base cover, ensure that there is no SD card installed in the SD card slot on your computer.
The following image(s) indicate the location of the touchpad and provides a visual representation of the removal procedure.
Steps
1.
Open the latch of the touchpad connector and disconnect the touchpad cable from the touchpad.
2.
Remove the five screws (M2x2) and seven screws (M2x1.8) that secure the touchpad bracket to the palm-rest and
keyboard assembly.
3.
Lift the touchpad bracket off the palm-rest and keyboard assembly.
4.
Lift the touchpad assembly off the palm-rest and keyboard assembly.
Removing and installing components
55