Dell Inspiron 16 7610 Service Manual for computers with three fans - Page 35

I/O board, Removing the I/O board

Get Dell Inspiron 16 7610 PDF manuals and user guides View all Dell Inspiron 16 7610 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

CAUTION: To avoid damaging the display, do not slide the palm-rest and keyboard assembly over the display assembly. 3. Close the left-display hinge and align the screw holes on the left-display hinge with the screw holes on the I/O board. 4. Replace the three screws (M2.5x5) that secure the left-display hinge to the palm-rest and keyboard assembly. 5. Close the right-display hinge and align the screw holes on the right-display hinge with the screw holes on the system board. 6. Replace the three screws (M2.5x5) that secure the right-display hinge to the palm-rest and keyboard assembly. 7. Connect the display cable to the connector on the system board. Next steps 1. Install the base cover. 2. Exit Service Mode. 3. Follow the procedure in After working inside your computer. I/O board Removing the I/O board Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Enter Service Mode. 3. Remove the base cover. About this task The following image(s) indicate the location of the I/O board and provides a visual representation of the removal procedure. Removing and installing components 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
CAUTION:
To avoid damaging the display, do not slide the palm-rest and keyboard assembly over the display
assembly.
3.
Close the left-display hinge and align the screw holes on the left-display hinge with the screw holes on the I/O board.
4.
Replace the three screws (M2.5x5) that secure the left-display hinge to the palm-rest and keyboard assembly.
5.
Close the right-display hinge and align the screw holes on the right-display hinge with the screw holes on the system board.
6.
Replace the three screws (M2.5x5) that secure the right-display hinge to the palm-rest and keyboard assembly.
7.
Connect the display cable to the connector on the system board.
Next steps
1.
Install the
base cover
.
2.
Exit
Service Mode
.
3.
Follow the procedure in
After working inside your computer
.
I/O board
Removing the I/O board
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Enter
Service Mode
.
3.
Remove the
base cover
.
About this task
The following image(s) indicate the location of the I/O board and provides a visual representation of the removal procedure.
Removing and installing components
35