Dell Latitude 7340 Service Manual - Page 40

Speakers, Removing the speakers for ultralight

Get Dell Latitude 7340 PDF manuals and user guides View all Dell Latitude 7340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Steps 1. Place the display assembly on a flat surface. 2. Slide the base assembly at an angle and gently press down on hinges to align the screw holes on the display hinges with screw holes on the system board. 3. Replace the four screws (M2.5x5) that secure the display hinges to the system board. 4. Connect and peel back the camera cable and display cable on the system board. 5. Replace the two screws (M2x3) that secures the camera cable bracket to the system board. 6. Replace the two screws (M2x3) that secures the EDP cable bracket to the system board. Next steps 1. Install the WWAN card. NOTE: This procedure applies only to computers shipped with a WWAN card installed. 2. Install the base cover. 3. Follow the procedure in After working inside your computer. Speakers Removing the speakers for ultralight Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the WWAN card. 40 Removing and installing components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Steps
1.
Place the display assembly on a flat surface.
2.
Slide the base assembly at an angle and gently press down on hinges to align the screw holes on the display hinges with
screw holes on the system board.
3.
Replace the four screws (M2.5x5) that secure the display hinges to the system board.
4.
Connect and peel back the camera cable and display cable on the system board.
5.
Replace the two screws (M2x3) that secures the camera cable bracket to the system board.
6.
Replace the two screws (M2x3) that secures the EDP cable bracket to the system board.
Next steps
1.
Install the
WWAN card
.
NOTE:
This procedure applies only to computers shipped with a WWAN card installed.
2.
Install the
base cover
.
3.
Follow the procedure in
After working inside your computer
.
Speakers
Removing the speakers for ultralight
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
3.
Remove the
WWAN card
.
40
Removing and installing components