Dell Latitude 7340 Service Manual - Page 51

Install the heat-sink after installing the system board as there are two screws M2x3 underneath

Get Dell Latitude 7340 PDF manuals and user guides View all Dell Latitude 7340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

1. Fingerprint reader 2. Darwin 1 antenna cable 3. Darwin 2 antenna cable 4. P sensor connector 5. LCD connector 6. IR-camera cable connector 7. M.2 solid-state drive connector 8. Battery cable connector 9. Speaker 2 10. Fan connector 11. Clickpad FFC connector 12. WLAN 13. USH daughter-board FFC connector 14. Speaker 1 15. WWAN NOTE: For computers shipped without a WWAN card, a WWAN shielding cover and WWAN bracket is pre-installed to the computer. As a result, follow the steps in the WWAN card removal/installation section to remove the WWAN shielding cover and WWAN bracket before removing the system board. CAUTION: Install the heat-sink after installing the system board as there are two screws (M2x3) underneath the heat-sink, that secure the system board to the computer, that need to be installed first. The following images indicate the location of the system board and provide a visual representation of the installation procedure. Removing and installing components 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
1.
Fingerprint reader
2.
Darwin 1 antenna cable
3.
Darwin 2 antenna cable
4.
P sensor connector
5.
LCD connector
6.
IR-camera cable connector
7.
M.2 solid-state drive connector
8.
Battery cable connector
9.
Speaker 2
10.
Fan connector
11.
Clickpad FFC connector
12.
WLAN
13.
USH daughter-board FFC connector
14.
Speaker 1
15.
WWAN
NOTE:
For computers shipped without a WWAN card, a WWAN shielding cover and WWAN bracket is pre-installed to the
computer. As a result, follow the steps in the WWAN card removal/installation section to remove the WWAN shielding
cover and WWAN bracket before removing the system board.
CAUTION:
Install the heat-sink after installing the system board as there are two screws (M2x3) underneath the
heat-sink, that secure the system board to the computer, that need to be installed first.
The following images indicate the location of the system board and provide a visual representation of the installation procedure.
Removing and installing components
51