Home » Dell Manuals » Hubs & Switches » Dell PowerConnect B - MLXe 4 » Manual Viewer

Dell PowerConnect B - MLXe 4 Hardware Installation Guide - Page 126

keyword indicates that the immediate synchronization applies to all interface modules, in the router.

View all Dell PowerConnect B - MLXe 4 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 126 highlights

5 Managing interface modules • You are prompted to synchronize the software images during the boot process. • You want to initiate an immediate synchronization; for example, you want an immediate update of the software images on one or all interface modules. • You want to disable synchronization; for example, you have upgraded the image of one interface module but want to continue running the older image on all other interface modules. The following sections discuss how to manage software image synchronization in these situations. Synchronizing the software image on interface modules during the boot process By default, the router checks the software images in the flash memory on interface modules during the boot process to see if they are the same as the images in the flash memory on the management module. If an interface module does not have a software image, the system automatically downloads the image from the management module to the interface module. If an interface module has an image that is different from that on the management module, the system prompts you to take one of the following steps: • To update the primary and secondary images on the interface module with the images on the management module, enter the lp cont-boot sync command at the Privileged EXEC prompt. • To retain the software images on the interface module, enter the lp cont-boot no-sync command at the Privileged EXEC prompt. Syntax: lp cont-boot sync Syntax: lp cont-boot no-sync Specifying an immediate synchronization To immediately synchronize software images between the management module and one or all interface modules, enter the following command at the Privileged EXEC level. PowerConnect# lp sync all Syntax: lp sync [all | ] • The all keyword indicates that the immediate synchronization applies to all interface modules in the router. • The parameter specifies the slot number that contains the interface module to which the immediate synchronization applies. You can specify 1 - 4 for 4-slot devices, 1 - 8 for 8-slot devices, or 1 - 16 for 16-slot devices. Specifying an immediate shutdown The management module takes approximately 16-20 seconds to shutdown all interface modules in a device after a reload is issued. During this time, the interface module continues sending packets. Enter the lp fast-powerdown command to immediately shut down all interface modules in a device after a reload is issued. PowerConnect(config)# lp fast-powerdown Syntax: [no] lp fast-powerdown If you do not enter this command, by default, the interface module continues to forward packets for an extended time after the router is reloaded. 114 PowerConnect B-MLXe Hardware Installation Guide 53-1002111-01

Section	Page
Audience	9
How this document is organized	9
Supported hardware	10
What’s new in this document	10
Document conventions	10
Text formatting	10
Command syntax conventions	10
Command examples	11
Notes, cautions, and danger notices	11
Notice to the reader	11
Getting technical help or reporting errors	12
Contacting Dell	12
Product Overview	13
Dell router overview	13
Router applications	13
Hardware features	13
PowerConnect B-MLXe routers	13
Router modules	18
Management modules	18
Interface modules	20
Switch fabric modules	27
High-speed switch fabric modules	29
Power supplies	29
Rack mounting brackets	30
Cooling system for PowerConnect B-MLXe routers	30
NIBI-16-FAN-EXH-A high-speed fan assemblies	32
Rack mount kit	33
Supported software features	33
Installing a PowerConnect B-MLXe Core Router	35
Installation precautions	35
General precautions	35
Power precautions	36
Installing a PowerConnect B-MLXe-4 router	37
Preparing the installation site	38
Unpacking a PowerConnect B-MLXe-4 router	38
Installing a PowerConnect B-MLXe-4 router in a rack or cabinet	38
Installing PowerConnect B-MLXe-4 modules	46
Installing power supplies in a PowerConnect B-MLXe-4 router	50
Connecting AC power	51
Final steps	52
Installing a PowerConnect B-MLXe-8 router	52
Preparing the installation site	52
Unpacking a PowerConnect B-MLXe-8 router	52
Installing a PowerConnect B-MLXe-8 router in a rack	53
Mounting your device in a cabinet	55
Installing PowerConnect B-MLXe-8 modules	60
Installing power supplies in the PowerConnect B-MLXe-8 router	63
Connecting AC power	64
Final steps	65
Installing a PowerConnect B-MLXe-16 router	65
Preparing the installation site	65
Unpacking a PowerConnect B-MLXe-16 router	66
Installing a PowerConnect B-MLXe-16 router in a rack	66
Installing modules in a PowerConnect B-MLXe 16-slot router	74
Installing power supplies in a PowerConnect B-MLXe-16 router	78
Final steps	80
Attaching a management station	80
Attaching a PC or terminal to the console port or Ethernet port	80
Activating the power source	81
Verifying proper operation	82
Observing the LEDs	82
Displaying the module status	84
Using the Dell Structured Cabling Components	87
Cable cinch overview	87
MRJ21 procedures	88
Cable cinch with two mRJ21 cables	88
Cable cinch with three mRJ21 cables	89
Cable cinch with four mRJ21 cables	90
Cable cinch with five mRJ21 cables	91
Cable cinch with six mRJ21 cables	92
Cable cinch with seven mRJ21 cables	93
Cable cinch with eight mRJ21 cables	94
RJ45 procedures	95
Cable cinch with one group of RJ45 cables	95
Cable cinch with two groups of RJ45 cables	96
Cable cinch with three groups of RJ45 cables	97
Cable cinch with four groups of RJ45 cables	98
Cable cinch with five groups of RJ45 cables	99
Cable cinch with six groups of RJ45 cables	100
Cable cinch with seven groups of RJ45 cables	101
Cable cinch with eight groups of RJ45 cables	102
Connecting a Router to a Network Device	103
Assigning permanent passwords	103
Configuring IP addresses	104
Support of subnet masks	104
Assigning an IP address to a management interface	105
Assigning IP addresses to an interface, virtual interface, or loopback interface	106
Enabling and disabling the interfaces	107
Understanding management port functions	107
Connecting the router to a network device	107
Installing a fiber-optic transceiver	108
Cabling a fiber-optic transceiver	108
Cleaning fiber-optic ports and connectors	108
Troubleshooting network connections	109
Testing network connectivity	109
Pinging an IP address	109
Tracing a route	110
Managing Routers and Modules	111
Managing the device	111
Disabling and re-enabling power to interface modules	111
Monitoring I2C failures on management modules	112
Displaying device status and temperature readings	114
Displaying the Syslog configuration and static and dynamic buffers	116
Managing switch fabric modules	118
Forcing HSF modules to operate in normal mode	118
Managing the cooling system	119
Configuring the cooling system	119
Manually setting the fan speed	123
Monitoring the cooling system	123
Temperature log reduction	124
Managing interface modules	125
Configuring interface module boot parameters	125
Changing priority of slots for interface modules	130
Disabling and re-enabling power to interface modules	131
Enabling and disabling management module CPU usage calculations	132
Displaying CPU usage	132
Displaying management module CPU usage	134
Removing MAC address entries	135
Upgrading Software Images and Configuration Files	137
Upgrading Software Images and Configuration Files	137
Important software upgrade considerations	138
General upgrade considerations	139
Special upgrade information for PowerConnect B-MLXe routers	139
Interface module software upgrade considerations	139
Important memory requirement information	140
CLI upgrade commands for R05.1.00	142
Software upgrade procedures	142
Determining current software image versions	143
Upgrading the combined IronWare Application Image on management modules	143
Upgrading the monitor image on a management module	143
Upgrading the boot image on a management module	144
Upgrading the boot and monitor images on interface modules	144
Upgrading interface modules using the combined FPGA image	145
Additional upgrade steps	146
Upgrading MBRIDGE images on management modules	146
Upgrading individual FPGA images on interface modules	147
Rebooting the management module	148
Performing a Hitless OS upgrade	149
Performing an image coherence check	149
Performing a coherence check without a reload	150
Displaying image versions	150
Using the show flash command	150
Configurations conditions specific to NI-MLX-1Gx48-T modules	157
Loading and saving configuration files	158
Configuring file size for startup and running configuration	158
Configuration buffers	159
Replacing the startup configuration with the running configuration	160
Replacing the startup configuration with the running configuration	160
Retaining the current startup configuration	160
Copying a configuration file to or from a TFTP server	161
Making local copies of the startup configuration file	161
Hitless OS upgrade	162
Dynamic configuration loading	164
Loading configuration information into the running-config file	166
Using SNMP to save and load configuration information	166
Erasing image and configuration files	167
File synchronization	167
File synchronization between active and standby management modules	167
File synchronization between management and interface modules	168
Scheduling a system reload	169
Reloading at a specific time	170
Reloading after a specific amount of time	170
Displaying the amount of time before a scheduled reload	170
Canceling a scheduled reload	170
Diagnostic error codes and remedies for TFTP transfers	170
Router Maintenance	173
Hardware maintenance schedule	173
Replacing a management module	173
Replacing an interface module	173
Removing and replacing an interface module	174
Replacing a switch fabric module	174
Replacing a fiber-optic transceiver	174
Cabling a fiber-optic transceiver	175
Replacing a power supply	175
Determining which power supply failed	175
Setting the threshold for power supply monitoring	176
Clearing power supply failure timestamps	176
Displaying power supply monitoring timestamps	177
Enabling a power supply shutdown	177
Powering on the power supply through the CLI	177
Replacing a power supply	178
Replacing fan assemblies	179
Replacing fan assemblies in a 16-slot router	179
Replacing the fan tray assembly in 4-slot and 8-slot routers	182
Replacing the air filters	184
Hardware Specifications	187
Hardware specifications for PowerConnect B-MLXe routers	187
Power specifications	187
Physical dimensions for PowerConnect B-MLXe routers	189
Operating environment specifications for PowerConnect B-MLXe routers	189
Storage environment specifications for PowerConnect B-MLXe routers	189
Safety agency approvals	189
Electromagnetic approvals	189
Port specifications for all router models	190
Console port pin assignments	190
Management port pin assignments	191
Power cords	191
Regulatory Statements	195
U.S.A.	195
Industry Canada statement	195
Europe and Australia	195
Germany	195
Japan	196
Power cords (Japan Denan)	196
China	197
Korea	197
Russia	197
Caution and Danger Notices	199
Cautions	199

Match case Limit results 1 per page

114

PowerConnect B-MLXe Hardware Installation Guide

53-1002111-01

Managing interface modules

•

You are prompted to synchronize the software images during the boot process.

•

You want to initiate an immediate synchronization; for example, you want an immediate update

of the software images on one or all interface modules.

•

You want to disable synchronization; for example, you have upgraded the image of one

interface module but want to continue running the older image on all other interface modules.

The following sections discuss how to manage software image synchronization in these situations.

Synchronizing the software image on interface modules during the boot process

By default, the router checks the software images in the flash memory on interface modules during

the boot process to see if they are the same as the images in the flash memory on the

management module. If an interface module does not have a software image, the system

automatically downloads the image from the management module to the interface module.

If an interface module has an image that is different from that on the management module, the

system prompts you to take one of the following steps:

•

To update the primary and secondary images on the interface module with the images on the

management module, enter the

lp cont-boot sync

slot-number

> command at the Privileged

EXEC prompt.

•

To retain the software images on the interface module, enter the

lp cont-boot no-sync

slot-number

> command at the Privileged EXEC prompt.

Syntax:

lp cont-boot sync

slot-number

Syntax:

lp cont-boot no-sync

slot-number

Specifying an immediate synchronization

To immediately synchronize software images between the management module and one or all

interface modules, enter the following command at the Privileged EXEC level.

PowerConnect# lp sync all

Syntax:

lp sync

[

all

<slot-number>

]

•

The

all

keyword indicates that the immediate synchronization applies to all interface modules

in the router.

•

The <

slot-number

> parameter specifies the slot number that contains the interface module to

which the immediate synchronization applies. You can specify 1 – 4 for 4-slot devices, 1 – 8 for

8-slot devices, or 1 – 16 for 16-slot devices.

Specifying an immediate shutdown

The management module takes approximately 16-20 seconds to shutdown all interface modules in

a device after a reload is issued. During this time, the interface module continues sending packets.

Enter the

lp fast-powerdown

command to immediately shut down all interface modules in a device

after a reload is issued.

PowerConnect(config)# lp fast-powerdown

Syntax:

[

]

lp fast-powerdown

If you do not enter this command, by default, the interface module continues to forward packets for

an extended time after the router is reloaded.