Dell PowerEdge PDU Metered LCD User Manual - Page 23

Installing the Rack Stabilizer Feet, Install stabilizer feet on the rack as follows

Get Dell PowerEdge PDU Metered LCD PDF manuals and user guides View all Dell PowerEdge PDU Metered LCD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Installing the Rack Stabilizer Feet CAUTION: Installing systems in a rack without the front and side stabilizer feet installed could cause the rack to tip over, potentially resulting in bodily injury under certain circumstances. Therefore, always install the stabilizer feet before installing components in the rack. Install stabilizer feet on the rack as follows: • Install front and side stabilizer feet on a standalone rack. • Install front stabilizer feet on all racks in a suite, and install a left or right stabilizer foot on the racks at each end of a suite. To install a front stabilizer foot, perform the following steps: 1 Open the front door. 2 Reach into the rack and pull up firmly on the stabilizer to detach it from the frame. 3 Position the front stabilizer foot against the base of the rack frame and align its holes with the corresponding holes in the frame. 4 Use a 5-mm Allen wrench and the provided Allen bolts to secure the front stabilizer foot to the rack as shown in Figure 1-9. Dell™ PowerEdge™ 4210 Installation Guide 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
Dell™ PowerEdge™ 4210 Installation Guide
21
Installing the Rack Stabilizer Feet
CAUTION:
Installing systems in a rack without the front and side stabilizer feet
installed could cause the rack to tip over, potentially resulting in bodily injury
under certain circumstances. Therefore, always install the stabilizer feet before
installing components in the rack.
Install stabilizer feet on the rack as follows:
•
Install front and side stabilizer feet on a standalone rack.
•
Install front stabilizer feet on all racks in a suite, and install a left or right
stabilizer foot on the racks at each end of a suite.
To install a front stabilizer foot, perform the following steps:
1
Open the front door.
2
Reach into the rack and pull up firmly on the stabilizer to detach it from
the frame.
3
Position the front stabilizer foot against the base of the rack frame and
align its holes with the corresponding holes in the frame.
4
Use a 5-mm Allen wrench and the provided Allen bolts to secure the front
stabilizer foot to the rack as shown in Figure 1-9.