Dell PowerEdge SC1430 Hardware Owner's Manual - Page 23

Plug & Play Configuration, See Troubleshooting a Hard Drive - sata

Get Dell PowerEdge SC1430 PDF manuals and user guides View all Dell PowerEdge SC1430 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Table 1-6. System Messages (continued) Message Causes Corrective Actions PCI BIOS failed to install PCI device BIOS (Option ROM) Reseat the expansion cards. Ensure that checksum failure is detected during all appropriate cables are securely shadowing. Loose cables to expansion connected to the expansion cards. If the card(s); faulty or improperly installed problem persists, see "Troubleshooting expansion card. Expansion Cards" on page 109. Plug & Play Configuration Error Error encountered in initializing PCI device; faulty system board. Install the RTCRST jumper and reboot the system. See Figure 6-1 for jumper location. If the problem persists, see "Troubleshooting Expansion Cards" on page 109. Read fault The operating system cannot read Requested sector not found from the diskette or hard drive, the system could not find a particular sector on the disk, or the requested sector is defective. Replace the diskette. Ensure that the diskette and hard drive cables are properly connected. See "Troubleshooting a USB Device" on page 99, "Troubleshooting a Diskette Drive" on page 105, or "Troubleshooting a Hard Drive" on page 107 for the appropriate drive(s) installed in your system. Remote configuration update attempt failed System unable to process Remote Configuration request. Retry Remote Configuration. ROM bad checksum = address Expansion card improperly installed or Reseat the expansion cards. Ensure that faulty. all appropriate cables are securely connected to the expansion cards. If the problem persists, see "Troubleshooting Expansion Cards" on page 109. SATA port n hard disk drive SATA cables are not properly seated, See "Troubleshooting a Hard Drive" on not found or drive missing. page 107. Sector not found Seek error Seek operation failed Faulty diskette or hard drive. See "Troubleshooting a Diskette Drive" on page 105 or "Troubleshooting a Hard Drive" on page 107 for the appropriate drive(s) installed in your system. Shutdown failure Shutdown test failure. See "Troubleshooting System Memory" on page 103. About Your System 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
About Your System
23
PCI BIOS failed to install
PCI device BIOS (Option ROM)
checksum failure is detected during
shadowing. Loose cables to expansion
card(s); faulty or improperly installed
expansion card.
Reseat the expansion cards. Ensure that
all appropriate cables are securely
connected to the expansion cards. If the
problem persists, see "Troubleshooting
Expansion Cards" on page 109.
Plug & Play Configuration
Error
Error encountered in initializing PCI
device; faulty system board.
Install the RTCRST jumper and reboot
the system. See Figure 6-1 for jumper
location. If the problem persists, see
"Troubleshooting Expansion Cards" on
page 109.
Read fault
Requested sector not found
The operating system cannot read
from the diskette or hard drive, the
system could not find a particular
sector on the disk, or the requested
sector is defective.
Replace the diskette. Ensure that the
diskette and hard drive cables are
properly connected. See
"Troubleshooting a USB Device" on
page 99, "Troubleshooting a Diskette
Drive" on page 105, or "Troubleshooting
a Hard Drive" on page 107 for the
appropriate drive(s) installed in your
system.
Remote configuration
update attempt failed
System unable to process Remote
Configuration request.
Retry Remote Configuration.
ROM bad checksum = address
Expansion card improperly installed or
faulty.
Reseat the expansion cards. Ensure that
all appropriate cables are securely
connected to the expansion cards. If the
problem persists, see "Troubleshooting
Expansion Cards" on page 109.
SATA port
n
hard disk drive
not found
SATA cables are not properly seated,
or drive missing.
See "Troubleshooting a Hard Drive" on
page 107.
Sector not found
Seek error
Seek operation failed
Faulty diskette or hard drive.
See "Troubleshooting a Diskette Drive"
on page 105 or "Troubleshooting a Hard
Drive" on page 107 for the appropriate
drive(s) installed in your system.
Shutdown failure
Shutdown test failure.
See "Troubleshooting System Memory"
on page 103.
Table 1-6.
System Messages
(continued)
Message
Causes
Corrective Actions