Home » Dell Manuals » Hubs & Switches » Dell S3048-ON » Manual Viewer

Dell S3048-ON VxFlex Network Deployment Guide using EMC Networking 25GbE switc - Page 41

Supported switches

Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

E Supported switches Steps in this document were validated using specific Dell EMC Networking switches and OS10EE but may be used for other Dell EMC Networking switch models that use the same networking operating system or later. Depending on a switch's available port numbers, speeds, and types, minor adjustments may be required to the example commands provided in this guide to achieve the same results. The table below shows all switches that can be configured using the directions provided in this guide. For the leaf switches, the switches must support OS10EE version 10.4.2.2 or later and must also support 25GbE connections. Supported switches for this deployment guide For the latest list of 25GbE switches from Dell EMC, visit Dell Networking S-Series 25-100GbE switches. 41 VxFlex Network Deployment Guide using Dell EMC Networking 25GbE switches and OS10EE

Section	Page
1 Introduction	6
1.1 Typographical conventions	6
1.2 Attachments	7
1.3 Dell EMC VxFlex	7
2 Hardware overview	8
2.1 Dell EMC Networking S3048-ON	8
2.2 Dell EMC Networking S5248F-ON	8
2.3 Dell EMC VxFlex Ready Node (R740xd)	8
3 VxFlex networking overview	9
3.1 Network topologies	9
3.1.1 Production network	9
3.1.2 Management network	10
3.2 Network connectivity	11
3.1 Connections to OOB management switch	12
3.2 IP addressing	14
3.3 Switch preparation	16
4 Dell EMC Networking S5248F-ON 25GbE switch configuration	18
4.1 Initializing switches	18
4.2 S5248F-ON leaf switch configuration	18
4.3 Verify switch configuration	20
4.3.1 show vlt domain id	20
4.3.2 show vlt domain id mismatch	21
4.3.3 show vlt domain id backup-link	21
4.3.4 show vlt mac-inconsistency	22
4.3.5 show spanning-tree brief	22
4.3.6 show vrrp brief	22
5 VMware virtual network design	23
5.1 ESXi management	23
5.2 Load balancing	23
5.3 Configuration details	23
5.4 VMware vSphere VMkernel configuration	25
6 Deploy Dell EMC VxFlex	27
6.1 Deploy the VxFlex plug-in	27
6.2 Upload the VxFlex OVA template	27
6.3 Deploy VxFlex using the deployment wizard	27
6.3.1 MDM Virtual IP Addresses	30
6.4 VxFlex GUI	31
7 Best practices	32
7.1 Maximum Transmission Unit size	32
7.2 Configure Quality of Service using DiffServ	34
A Troubleshoot SDS connectivity	36
B Routing VxFlex Virtual Machine traffic	37
C Validated hardware and components	39
D Validated software	40
E Supported switches	41
F Product manuals and technical guides	42
G Fabric Design Center	43

Match case Limit results 1 per page

VxFlex Network Deployment Guide using Dell EMC Networking 25GbE switches and OS10EE

Supported switches

Steps in this document were validated using specific Dell EMC Networking switches and OS10EE but may be

used for other Dell EMC Networking switch models that use the same networking operating system or later.

Depending on a

switch’s available port numbers, speeds, and types, minor adjustments may be required to

the example commands provided in this guide to achieve the same results.

The table below shows all switches that can be configured using the directions provided in this guide. For the

leaf switches, the switches must support OS10EE version 10.4.2.2 or later and must also support 25GbE

connections.

Supported switches for this deployment guide

For the latest list of 25GbE switches from Dell EMC, visit

Dell Networking S-Series 25-100GbE switches