Home » Dell Manuals » Hubs & Switches » Dell S4148U-ON » Manual Viewer

Dell S4148U-ON EMC Networking OS10EE FCoE Deployment with FSB - Page 32

show fc zoneset

Get Dell S4148U-ON PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

8.5 show fc zoneset The show fc zoneset active command shows the zones and zone members in the configured zone sets. Members that are logged into the fabric are shown with an asterisk (*). S4148U-F-Port-1# show fc zoneset ZoneSetName ZoneName ZoneMember zoneset1 r740xd-1p1zone SpA-0 SpB-0 r740xd-1p1 r740xd-2p1zone SpA-0 SpB-0 r740xd-2p1 r740xd-3p1zone SpA-0 SpB-0 r740xd-3p1 r740xd-4p1zone SpA-0 SpB-0 r740xd-4p1 vFabric id: 101 Active Zoneset: zoneset1 ZoneName ZoneMember r740xd-1p1zone *20:01:f4:e9:d4:61:c6:6a *50:06:01:66:47:e0:1b:19 *50:06:01:6e:47:e0:1b:19 r740xd-2p1zone *20:01:f4:e9:d4:62:4a:d0 *50:06:01:66:47:e0:1b:19 *50:06:01:6e:47:e0:1b:19 r740xd-3p1zone *20:01:f4:e9:d4:62:4b:72 *50:06:01:66:47:e0:1b:19 *50:06:01:6e:47:e0:1b:19 r740xd-4p1zone *20:01:f4:e9:d4:62:4b:ba *50:06:01:66:47:e0:1b:19 *50:06:01:6e:47:e0:1b:19 32 Dell EMC Networking OS10EE FCoE Deployment with FSB

Section	Page
1 Introduction	6
1.1 Typographical conventions	7
1.2 Attachments	7
2 Hardware Overview	8
2.1 Dell EMC PowerSwitch models	8
2.1.1 Dell EMC PowerSwitch S5248-ON	8
2.1.2 Dell EMC PowerSwitch S4148U-ON	8
2.1.3 Dell EMC PowerSwitch S3048-ON	8
2.2 Storage arrays, Fibre Channel switches, and servers	9
2.2.1 Dell EMC Unity 500F storage array	9
2.2.2 Dell EMC PowerEdge R740xd server	9
3 Topology overview	10
3.1 FC SAN topology detail	10
3.2 OOB management network	11
4 Deployment overview	13
4.1 Configuration strategy and sequence	13
4.1.1 FC storage array	13
4.1.2 Dell EMC PowerSwitch S4148U-ON switches for FC SAN	13
4.1.3 Dell EMC PowerSwitch S5248-ON leaf switches as FSBs	13
4.1.4 Server HW and Virtualization	13
5 S5248-ON FSB leaf switch configuration	14
5.1 Prepare switches	14
5.1.1 Factory default configuration	14
5.2 Configure switches	14
5.2.1 Configure global switch settings	14
5.2.2 Configure VLT between the two S5248-ON switches	15
5.2.3 Configure FSB	15
5.2.4 Configure QoS	16
5.2.5 Configure VLAN interfaces	17
5.2.6 Configure VRRP	18
5.2.7 Configure server-facing interfaces	18
5.2.8 Configure upstream interfaces	19
5.2.9 Configure BGP routing	20
5.2.10 Configure uplink failure detection (UFD)	21
6 S4148U-ON FCF switch configuration	22
6.1 Prepare switches	22
6.1.1 Factory default configuration	22
6.1.2 Set switch port profile	22
6.2 Configure switches	22
6.2.1 Configure global switch settings	23
6.2.2 Configure FC aliases and FC zoning	23
6.2.3 Configure the VLAN and virtual fabrics	24
6.2.4 Configure the FCoE interfaces to the leaf switches	24
6.2.5 Configure QoS	25
7 S5248-ON FSB validation	27
7.1 show interface status	27
7.2 show vlan	27
7.3 show fcoe sessions	28
7.4 show fcoe fcf	28
7.5 show fcoe enode	28
8 S4148U-ON FCF (F_Port) validation	29
8.1 show interface status	29
8.2 show vlan	29
8.3 show fcoe system	29
8.4 show fc ns switch	30
8.5 show fc zoneset	32
8.6 show vfabric	33
A Validated components	34
B PowerEdge server, Unity storage, and VMware setup	35
B.1 PowerEdge server configuration	35
B.1.1 Reset server CNA interfaces to factory defaults	35
B.1.2 Determine FCoE CNA port WWPNs	35
B.2 Dell EMC Unity 500F storage array configuration	37
B.2.1 Create a storage pool	38
B.2.2 Add ESXi hosts	38
B.2.3 Create LUNs and configure host access	39
B.3 VMware preparation	40
B.3.1 VMware ESXi download and installation	40
B.3.2 Install and configure VMware vCenter Server 6.7 U1	40
B.3.3 Add ESXi hosts to vCenter Server	40
B.3.4 Configure storage on ESXi hosts	41
B.3.5 Rescan storage	41
B.3.6 Create a datastore	42
B.3.7 Create a virtual disk	43
B.3.8 Configure the virtual disk in Windows Server	45
C Technical resources	46