Dell S4148U-ON EMC Networking OS10EE FCoE Deployment with FSB - Page 35

PowerEdge server, Unity storage, and VMware setup

Get Dell S4148U-ON PDF manuals and user guides View all Dell S4148U-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

B PowerEdge server, Unity storage, and VMware setup B.1 PowerEdge server configuration This section details the configuration of the CNAs used to validate the network topology. Note: Exact iDRAC steps in this section may vary depending on hardware, software and browser versions used. See the PowerEdge server documentation for steps to connect to the iDRAC. B.1.1 Reset server CNA interfaces to factory defaults Note: Resetting to defaults is only necessary if installed CNA has been modified from their factory default settings. 1. Connect to the server's iDRAC in a web browser and launch the virtual console. 2. In the virtual console, from the Next Boot menu, select BIOS Setup. 3. Reboot the server. 4. From the System Setup Main Menu, select Device Settings. 5. From the Device Settings page, select the first CNA adapter port. 6. From the Main Configuration Page, click Default and then Yes to load the default settings. 7. Click OK and then click Finish. 8. Click Yes to save changes. Click OK. 9. Repeat steps 5 through 8 for the second FC adapter port. 10. Repeat steps 1 through 9 for remaining servers. B.1.2 Determine FCoE CNA port WWPNs The FCoE CNA World Wide Port Names (WWPNs) for the PowerEdge R740xd server are used for FC zone configuration. WWPNs may be determined using the iDRAC as follows: 1. Connect to the first server's iDRAC in a web browser and log in. 2. Select System > Network Devices. 3. Under Network Devices, click the CNA. Note: In this example, click NIC Slot 2. The NIC ports are displayed as shown in Figure 9. 35 Dell EMC Networking OS10EE FCoE Deployment with FSB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
35
Dell EMC Networking OS10EE FCoE Deployment with FSB
B
PowerEdge server, Unity storage, and VMware setup
B.1
PowerEdge server configuration
This section details the configuration of the CNAs used to validate the network topology.
Note:
Exact iDRAC steps in this section may vary depending on hardware, software and browser versions
used. See the PowerEdge server documentation for steps to connect to the iDRAC.
B.1.1
Reset server CNA interfaces to factory defaults
Note:
Resetting to defaults is only necessary if installed CNA has been modified from their factory default
settings.
1.
Connect to the server's iDRAC in a web browser and launch the virtual console.
2.
In the virtual console, from the
Next Boot
menu, select
BIOS Setup
.
3. Reboot the server.
4.
From the System Setup Main Menu, select
Device Settings
.
5. From the
Device Settings
page, select the first CNA adapter port.
6. From the
Main Configuration Page
, click
Default
and then
Yes
to load the default settings.
7. Click
OK
and then click
Finish
.
8. Click
Yes
to save changes. Click
OK
.
9.
Repeat steps 5 through 8 for the second FC adapter port.
10. Repeat steps 1 through 9 for remaining servers.
B.1.2
Determine FCoE CNA port WWPNs
The FCoE CNA World Wide Port Names (WWPNs) for the PowerEdge R740xd server are used for FC zone
configuration. WWPNs may be determined using the iDRAC as follows:
1.
Connect to the first server's iDRAC in a web browser and log in.
2. Select
System
>
Network Devices
.
3. Under
Network Devices
, click the CNA.
Note
: In this example, click NIC Slot 2. The NIC ports are displayed as shown in Figure 9.