Dell Vostro 5502 Service Manual - Page 50

Installing the DC-in port

Get Dell Vostro 5502 PDF manuals and user guides View all Dell Vostro 5502 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Steps 1. Locate the DC-in port on your computer. 2. Remove the three (M2.5x3.5) screws, and lift the metal hinge bracket covering the display connector. 3. Remove the single (M2x3) screw, and lift the DC-in port. 4. Peel the transparent sticker, and disconnect the DC-in cable from its connector on the system board. 5. Peel the adhesive tape off. 6. Remove the DC-in port from the palm-rest and keyboard assembly. Installing the DC-in port Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the DC-in port and provides a visual representation of the installation procedure. Steps 1. Locate the DC-in port on your laptop. 2. Replace the single (M2x3) screw, and connect the DC-in cable to the system board. 3. Adhere the adhesive tape and the transparent sticker. 4. Lower the metal hinge and align the screw holes on the system board. 50 Disassembly and reassembly

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Steps
1.
Locate the DC-in port on your computer.
2.
Remove the three (M2.5x3.5) screws, and lift the metal hinge bracket covering the display connector.
3.
Remove the single (M2x3) screw, and lift the DC-in port.
4.
Peel the transparent sticker, and disconnect the DC-in cable from its connector on the system board.
5.
Peel the adhesive tape off.
6.
Remove the DC-in port from the palm-rest and keyboard assembly.
Installing the DC-in port
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the DC-in port and provides a visual representation of the installation procedure.
Steps
1.
Locate the DC-in port on your laptop.
2.
Replace the single (M2x3) screw, and connect the DC-in cable to the system board.
3.
Adhere the adhesive tape and the transparent sticker.
4.
Lower the metal hinge and align the screw holes on the system board.
50
Disassembly and reassembly