Dell Vostro 5502 Service Manual - Page 54

Installing the touchpad

Get Dell Vostro 5502 PDF manuals and user guides View all Dell Vostro 5502 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

4. Open the latch, and disconnect the touchpad cable from the system board. 5. Remove the adhesive tape from the touchpad bracket. 6. Remove the two (M2x2) screws that secure the touchpad bracket to the palm-rest and keyboard assembly. 7. Lift the touchpad, along with the cable, off the palm-rest and keyboard assembly. Installing the touchpad Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the component and provides a visual representation of the installation procedure. Steps 1. Align and place the touchpad into the slot on the palm-rest and keyboard assembly. 2. Replace the two (M2x2) screws along with the bracket to secure the touchpad to the palm-rest and keyboard assembly. 3. Slide the touchpad cable onto its connector on the system board and close the latch to secure the cable. 4. Adhere the adhesive tape back on touchpad bracket. 54 Disassembly and reassembly

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
4.
Open the latch, and disconnect the touchpad cable from the system board.
5.
Remove the adhesive tape from the touchpad bracket.
6.
Remove the two (M2x2) screws that secure the touchpad bracket to the palm-rest and keyboard assembly.
7.
Lift the touchpad, along with the cable, off the palm-rest and keyboard assembly.
Installing the touchpad
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the component and provides a visual representation of the installation procedure.
Steps
1.
Align and place the touchpad into the slot on the palm-rest and keyboard assembly.
2.
Replace the two (M2x2) screws along with the bracket to secure the touchpad to the palm-rest and keyboard assembly.
3.
Slide the touchpad cable onto its connector on the system board and close the latch to secure the cable.
4.
Adhere the adhesive tape back on touchpad bracket.
54
Disassembly and reassembly