Dell W-7024 Controller Installation Guide - Page 16

USB Interface, Serial Console Port

Get Dell W-7024 PDF manuals and user guides View all Dell W-7024 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

USB Interface The W-7024 controller is equipped with a USB 2.0 interface on the back panel of the controller. A USB storage device can be used to save and upload configurations to the controller. USB functions are controlled through the LCD panel on the front of the controller. For more information on the LCD panel and its functions, see "LCD Panel" on page 14. Serial Console Port For direct local management of the controller, use the serial console port located on the back panel of the controller. The port is an RJ-45 female connector that accepts an RS-232 serial cable with a male connector. Figure 5: Serial Console Port Pin-Out Serial Console Port RJ-45 Female Pin-Out 1 2 3 4 5 6 7 8 Direction Input Output TxD GND GND RxD The communication settings for the console port are shown in the following table: Table 12: Console Terminal Settings Baud Rate Data Bits 9600 8 Parity None Stop Bits 1 Flow Control None CAUTION: The Console port is compatible only with RS-232 devices. Non-RS-232 devices, such as APs, are not supported. ATTENTION: Le port CONSOLE est compatible uniquement avec les périphériques RS-232. Les périphériques qui ne sont pas de type RS-232, notamment les points d'accès, ne sont pas pris en charge. CAUTION: Do not connect the Console port to an Ethernet switch or a PoE power source. This may damage the controller. ATTENTION: Ne connectez pas le port Console sur un commutateur Ethernet ou une source d'alimentation PoE. Sinon, vous risquez d'endommager le contrôleur. Serial Console Port Adaptor A modular adaptor can be used to convert the female RJ-45 connector to a male DB9 connector. See Figure 6 for details. Dell Networking W-7024 Controller | Installation Guide W-7024 Controller | 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
USB Interface
The W-7024 controller is equipped with a USB 2.0 interface on the back panel of the controller. A USB storage
device can be used to save and upload configurations to the controller. USB functions are controlled through the
LCD panel on the front of the controller. For more information on the LCD panel and its functions, see
"LCD
Panel" on page 14
.
Serial Console Port
For direct local management of the controller, use the serial console port located on the back panel of the controller.
The port is an RJ-45 female connector that accepts an RS-232 serial cable with a male connector.
Figure 5:
Serial Console Port Pin-Out
Serial
Console Port
1
2
3
4
5
6
7
8
TxD
GND
RxD
RJ-45 Female
Pin-Out
Direction
Input
Output
GND
The communication settings for the console port are shown in the following table:
Baud Rate
Data Bits
Parity
Stop Bits
Flow Control
9600
8
None
1
None
Table 12:
Console Terminal Settings
CAUTION: The Console port is compatible only with RS-232 devices. Non-RS-232 devices, such as APs, are not supported.
ATTENTION: Le port CONSOLE est compatible uniquement avec les périphériques RS-232. Les périphériques qui ne sont pas de type
RS-232, notamment les points d’accès, ne sont pas pris en charge.
CAUTION: Do not connect the Console port to an Ethernet switch or a PoE power source. This may damage the controller.
ATTENTION: Ne connectez pas le port Console sur un commutateur Ethernet ou une source d’alimentation PoE. Sinon, vous risquez
d’endommager le contrôleur.
Serial Console Port Adaptor
A modular adaptor can be used to convert the female RJ-45 connector to a male DB9 connector. See
Figure 6
for
details.
Dell Networking W-7024 Controller |
Installation Guide
W-7024 Controller | 16