Dell W-7024 Controller Installation Guide - Page 25

Disconnecting the AC Power Cord, Installing an SFP/SFP+ Module, Connecting an LC Fiber Optic Cable

Get Dell W-7024 PDF manuals and user guides View all Dell W-7024 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Disconnecting the AC Power Cord To disconnect the AC power cord from the W-7024 controller: 1. Lift the power cord retaining clip off the AC power cord. 2. Pull the AC power cord from the AC connector. 3. The W-7024 controller is now turned Off. Installing an SFP/SFP+ Module NOTE: Use standard ESD precautions when installing or removing an SFP/SFP+ module. To install an SFP/SFP+ module into the W-7024 controller: 1. Slide the SFP/SFP+ module, top side facing upward, into a 10GBASE-X port until a connection is made and an audible click is heard. Figure 14: Installing an SFP/SFP+ Removing an SFP/SFP+ Module To remove an SFP/SFP+ module: 1. Open and release the latch on the SFP/SFP+ module. 2. Pull and remove the module from the port. Connecting an LC Fiber Optic Cable To connect an LC fiber optic cable into an SFP-SX or SFP-LX module: 1. Clean the fiber optic cable connector before inserting it into the SFP/SFP+ module. 2. Insert the fiber optic cable into the SFP/SFP+ module. Ensure that the latch on the cable faces the top of the SFP/SFP+ module (see Figure 15). 3. Slide the cable into place until a connection is made and an audible click is heard. 25 | Installation Dell Networking W-7024 Controller | Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
25
| Installation
Dell Networking W-7024 Controller | Installation Guide
Disconnecting the AC Power Cord
To disconnect the AC power cord from the W-7024 controller:
1.
Lift the power cord retaining clip off the AC power cord.
2.
Pull the AC power cord from the AC connector.
3.
The W-7024 controller is now turned Off.
Installing an SFP/SFP+ Module
NOTE:
Use standard ESD precautions when installing or removing an SFP/SFP+ module.
To install an SFP/SFP+ module into the W-7024 controller:
1.
Slide the SFP/SFP+ module, top side facing upward, into a 10GBASE-X port until a connection is made and an
audible click is heard.
Figure 14:
Installing an SFP/SFP+
Removing an SFP/SFP+ Module
To remove an SFP/SFP+ module:
1.
Open and release the latch on the SFP/SFP+ module.
2.
Pull and remove the module from the port.
Connecting an LC Fiber Optic Cable
To connect an LC fiber optic cable into an SFP-SX or SFP-LX module:
1.
Clean the fiber optic cable connector before inserting it into the SFP/SFP+ module.
2.
Insert the fiber optic cable into the SFP/SFP+ module. Ensure that the latch on the cable faces the top of the
SFP/SFP+ module (see
Figure 15
).
3.
Slide the cable into place until a connection is made and an audible click is heard.