Dell Wyse 3020 Wyse ThinOS Version 8.5 INI Reference Guide - Page 21

Table 6. Connection Settings: wnos.ini, Gateway PNAgent Interface PNAgent/Lite servers in

Get Dell Wyse 3020 PDF manuals and user guides View all Dell Wyse 3020 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Table 6. Connection Settings: wnos.ini files only Parameter AddCertificate=filename password={plain text password} Password-enc={encrypted password} CaradigmServer=vip list [EGPGroup=group name] [EnableLogOff={yes,no}] [SecurityMode={default, full, warning, low}] [DisableManualLogon=yes, no] Community=community [Encrypt={yes, no}] ConnectionBroker={default, VMware, Microsoft, Quest, AWS} [IgnoreProfile={yes, no,}] Description AddCertificate - Specifies a certificate file residing in the subfolder cacerts under the wnos folder to load on platforms with nand flash, or on the memory. The length of the filename, including the trailing period and the file extension, is limited to 64 characters. AddCertificate must be used when configuring the Citrix Secure Gateway PNAgent Interface (PNAgent/Lite servers) in the Network Setup dialog box. Adding certificates are required if the user CSG environments use certificate agents that are not covered by the built-in certificates. The certificates are used to validate server identities by the thin client. Supported files include .crt file on ICA CSG; .cer and .pfx in 802.1x. Password and Password-Enc are specially used with PFX files. CaradigmServer=vip list contains a list of VIP addresses with optional TCP port number of Caradigm servers. EGPGroup defines the user group name. If EnableLogOff=yes is specified, the user is logged off from the session before system signs off. Otherwise the session is disconnected. The logged off user has a timeout value which can be set using SessionConfig parameter SessionLogOffTimeout. The default timeout value is 1, if no SessionLogOffTimeout is specified. SecurityMode specifies the SSL certification validation policy. If set to default, it applies the SecurityPolicy setting. If set to full, the SSL connection needs to verify server certificate. If it is untrusted, drop the connection. If set to warning, the SSL connection needs to verify server certificate. If it is untrusted, it is up to you to continue or drop the connection. If set to low, the server certificate is not checked. The value is persistent, the default value of the setting is default. DisableManualLogon is set to yes to disable user to manually enter credentials to authenticate into the device. It only allows an already enrolled proximity badge and in active grace period to authenticate with a single badge tap. The default value is no Specifies the SNMP community name. A string up to 31 characters are allowed. After the value is specified, it is saved in the nonvolatile memory. If encrypt=yes, an encrypted string is used as a community name. The default value is set to no. NOTE: Use our Windows Password_Gen tool or built-in tool to generate the encrypted string. Default value is default. Specifies the type of VDI broker to use. Default is a 3rd party VDI broker. Parameters for wnos INI files only 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
Table 6. Connection Settings: wnos.ini
files
only
Parameter
Description
AddCertificate=filename
password={plain text password}
Password-enc={encrypted password}
AddCertificate
—
Specifies
a
certificate
file
residing in the
subfolder cacerts under the wnos folder to load on platforms with
nand
flash,
or on the memory. The length of the
filename,
including
the trailing period and the
file
extension, is limited to 64 characters.
AddCertificate
must be used when
configuring
the Citrix Secure
Gateway PNAgent Interface (PNAgent/Lite servers) in the
Network Setup
dialog box.
Adding
certificates
are required if the user CSG environments use
certificate
agents that are not covered by the built-in
certificates.
The
certificates
are used to validate server identities by the thin
client. Supported
files
include .crt
file
on ICA CSG; .cer and .pfx in
802.1x. Password and Password-Enc are specially used with PFX
files.
CaradigmServer=vip list
[EGPGroup=group name]
[EnableLogOff={yes,
no}]
[SecurityMode={
default, full, warning, low}]
[DisableManualLogon=yes,
no]
CaradigmServer=vip list contains a list of VIP addresses with
optional TCP port number of Caradigm servers. EGPGroup
defines
the user group name. If
EnableLogOff=yes
is
specified,
the user is
logged
off
from the session before system signs
off.
Otherwise the
session is disconnected. The logged
off
user has a timeout value
which can be set using
SessionConfig
parameter
SessionLogOffTimeout.
The default timeout value is 1, if no
SessionLogOffTimeout
is
specified.
SecurityMode
specifies
the SSL
certification
validation policy.
If set to default, it applies the SecurityPolicy setting.
If set to full, the SSL connection needs to verify server
certificate.
If it is untrusted, drop the connection.
If set to warning, the SSL connection needs to verify server
certificate.
If it is untrusted, it is up to you to continue or drop the connection.
If set to low, the server
certificate
is not checked. The value is
persistent, the default value of the setting is default.
DisableManualLogon is set to yes to disable user to manually enter
credentials to authenticate into the device. It only allows an already
enrolled proximity badge and in active grace period to authenticate
with a single badge tap. The default value is no
Community=community
[Encrypt={yes,
no}]
Specifies
the SNMP community name. A string up to 31 characters
are allowed. After the value is
specified,
it is saved in the non-
volatile memory.
If encrypt=yes, an encrypted string is used as a community name.
The default value is set to no.
NOTE:
Use our Windows Password_Gen tool or built-in
tool to generate the encrypted string.
ConnectionBroker={
default, VMware, Microsoft, Quest, AWS}
[IgnoreProfile={yes,
no,}]
Default value is
default
.
Specifies
the type of VDI broker to use.
Default is a 3rd party VDI broker.
Parameters for wnos INI
files
only
21