Dell XPS M140 MXC051 XPS M140 Service Manual - Page 40

Display Assembly and Display Latch: Dell™ XPS M140 Service Manual, Display Assembly

Get Dell XPS M140 MXC051 PDF manuals and user guides View all Dell XPS M140 MXC051 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Back to Contents Page Display Assembly and Display Latch Dell™ XPS M140 Service Manual Display Assembly Display Bezel Display Panel Display Latch Display Assembly Removing the Display Assembly CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1. Follow the instructions in Preparing to Work Inside the Computer. 2. Remove the hinge cover (see Removing the Hinge Cover). 3. Remove the keyboard (see Removing the Keyboard). 4. Open the display all the way (180 degrees) so that it rests flat against your work surface. 5. Use the pull-tab to disconnect the display cable from the system board. 6. Remove the Mini PCI antenna cables from the retaining clips on the base of the computer and pull apart the connectors. 7. Remove the four M2.5 x 5-mm screws (two on each side) that connect the display assembly to the computer. 8. Lift the display assembly straight out of the computer.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Back to Contents Page
Display Assembly and Display Latch
Dell™ XPS M140 Service Manual
Display Assembly
Display Bezel
Display Panel
Display Latch
Display Assembly
Removing the Display Assembly
CAUTION:
Before you perform any of the procedures in this section, follow the safety instructions in the
Product Information Guide
.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically
touching an unpainted metal surface (such as the back panel) on the computer.
1. Follow the instructions in
Preparing to Work Inside the Computer
.
2. Remove the hinge cover (see
Removing the Hinge Cover
).
3. Remove the keyboard (see
Removing the Keyboard
).
4. Open the display all the way (180 degrees) so that it rests flat against your work surface.
5. Use the pull-tab to disconnect the display cable from the system board.
6. Remove the Mini PCI antenna cables from the retaining clips on the base of the computer and pull apart the
connectors.
7. Remove the four M2.5 x 5-mm screws (two on each side) that connect the display assembly to the computer.
8. Lift the display assembly straight out of the computer.