Denon AVR 1603 Owners Manual - Page 25

LAST FUNCTION MEMORY, 17. INITIALIZATION OF THE MICROPROCESSOR, NOTES, Turning on the main unit

Get Denon AVR 1603 - AV Receiver PDF manuals and user guides View all Denon AVR 1603 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

ENGLISH 26 16 LAST FUNCTION MEMORY • This unit is equipped with a last function memory which stores the input and output setting conditions as they were immediately before the power is switched off. • The unit is also equipped with a back-up memory. This function provides approximately one week of memory storage when the main unit's power operation switch is off and with the power cord disconnected. 17 INITIALIZATION OF THE MICROPROCESSOR When the indication of the display is not normal or when the operation of the unit does not shows the reasonable result, the initialization of the microprocessor is required by the following procedure. 1 Switch off the unit using the main unit's power operation switch. 2 Hold the following SPEAKER A button and B button, and turn the main unit's power operation switch on. 1, 2 2 3 Check that the entire display is flashing with an interval of about 1 second, and release your fingers from the 2 buttons and the microprocessor will be initialized. NOTES: • If step 3 does not work, start over from step 1. • If the microprocessor has been reset, all the button settings are reset to the default values (the values set upon shipment from the factory). Turning on the main unit's power from the standby mode without using the remote control unit • Press the power switch on the main unit while pressing the INPUT MODE button on the main unit's panel to turn on the power.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
26
ENGLISH
16
LAST FUNCTION MEMORY
•
This unit is equipped with a last function memory which stores the input and output setting conditions as they
were immediately before the power is switched off.
•
The unit is also equipped with a back-up memory. This function provides approximately one week of memory
storage when the main unit
’
s power operation switch is off and with the power cord disconnected.
17
INITIALIZATION OF THE MICROPROCESSOR
When the indication of the display is not normal or when the operation of the unit does not shows the reasonable
result, the initialization of the microprocessor is required by the following procedure.
2
1, 2
1
Switch off the unit using the main unit
’
s power
operation switch.
2
Hold the following SPEAKER A button and B
button, and turn the main unit
’
s power operation
switch on.
3
Check that the entire display is flashing with an
interval of about 1 second, and release your fingers
from the 2 buttons and the microprocessor will
be initialized.
NOTES:
•
If step 3 does not work, start over from step 1.
•
If the microprocessor has been reset, all the
button settings are reset to the default values
(the values set upon shipment from the factory).
Turning on the main unit
’
s power from the standby mode without using the remote control unit
•
Press the power switch on the main unit while pressing the INPUT MODE button on the main unit
’
s panel
to turn on the power.